510017 ARM-USB-OCD-H HIGH SPEED 3-IN-1 FAST USB ARM JTAG

ARM-USB-OCD-H HIGH SPEED 3-IN-1 FAST USB ARM JTAG

First on market three-in-one USB JTAG debugger - offers JTAG + RS232 (full modem signals supported) port + power supply all in one compact device
Categories
Prices are VAT included
€63.68 Price
€52.20 + VAT

Qty
 

Details


FEATURES

  • First on market three-in-one USB JTAG debugger - offers JTAG + RS232 (full modem signals supported) port + power supply all in one compact device
  • High speed USB 2.0 JTAG dongle interface, can be used with all ARM devices for programming and debugging.
  • uses ARM's standard 2x10 pin JTAG connector
  • supports ARM targets working in voltage range 1.65 – 5.0 V DC
  • software supported by OpenOCD (open source) debugger
  • adds virtual RS232 port to your computer with all modem signals like: DTR, DSR, DCD, RTS, CTS, Rx, Tx
  • can be used as power supply to your target board with three jumper selectable power supplies: 5V 9V and 12VDC,
    USB source current is limited with resetable fuse at 300mA, at the different output voltage the maximum current is
    different: 5V/200mA, note that this also depend on your USB host current capabilities, if other
    USB devices are attached to your computer or if the laptop is running on batteries these figures may be different and
    depend on your computer USB host.
  • comes with CD with Windows installer for full featured and open source tools as alternative to the commercial ARM
    development packages: GCC C compiler, openOCD debugger and Eclipse IDE.
  • Works with IAR EW-ARM 5.50 or newer
  • dimensions 50x40 mm (2x1.6") + 20 cm (8") JTAG cable + 30 cm (12") power supply cable

DOCUMENTS:

HARDWARE:

SOFTWARE:

  • Olimex's ARM GCC for Windows Dummies install CD - installs on your computer WinARM + OpenOCD debugger + Eclipse for out of the box development with the open source GNU C compiler and OpenOCD debugger, supports flash loading on LPC and external flash for LPC-H2214, LPC-H2294, with make examples for different ARM controllers. The current revision of the CD is REV.G check the CD content.
  • Drivers for working with OpenOCD 0.1.0 , Drivers for CrossWorks (FTDI drivers) , EEPROM content
  • openOCD open source debugger from Dominic Rath for debugging with Insight/GDB.
  • WinARM - easy to install open source GCC toolchain by Martin Thomas. We are working on CD install package for WinArm+OpenOCD+ARM-USB-OCD support
  • CrossWorks - commercial IDE version 1.7 supports all Olimex JTAGs, personal licensees start from US $125(!)
  • Building GCC for ARM tutorial
  • Building GCC for Cortex tutorial
  • Using OpenOCD tutorial
  • Installing OpenOcd-Rev. G drivers for Windows 7.pdf
  • For the moment the only supported package is GCC C compiler + openOCD debugger + Eclipse IDE. Olimex can provide the necessary information and cooperate with interested parties if they want to add low cost USB debugger support to their C compilers and IDEs.

FAQ:

Q: Can I use ARM-USB-OCD-H with EW-ARM?
A: IAR supports GDB and works with ARM-USB-OCD-H

Q: I use Windows XP x64, how I can update the USB drivers?
A: FTDI have x64 drivers on their web, download them and use our ARM-USB-OCD PID: 0x0003, VID: 0x15BA to install the drivers.

Q: how to install ARM-USB-OCD-H to work with CrossWorks:
A: Use: "Generic FTD2232" target interface
1. Right click on a blank space in the targets window and select "New Target Interface > Generic FT2232 Device".
2. Right click on the new target interface and select "Properties" - set the following properties:
nSRST Inversion Mask 0x0200
nSRST Mask = 0x0200
nTRST Inversion Mask = 0x0000
nTRST Mask - 0x0400
Output Pins = 0x0F1B
Output Value = 0x0408
PID: 0x002B
VID: 0x15BA

In CrossWorks 1.7 there are Target interfaces for Olimex JTAGs, note that RTCK is not used with FT2232 design so your JTAG clock should not exceed 1/6 of your target MCU clock or the JTAG will lock up, start with JTAG divider 10 and decrease until you are able to debug to find your own value for your target.

Q: Can I debug high voltage targets with ARM-USB-OCD-H?
A: ARM-USB-OCD-H is not isolated, but you can use USB-ISO isolator device to protect your PC while debugging high voltage targets.

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on ARM-USB-OCD-H HIGH SPEED 3-IN-1 FAST USB ARM JTAG

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.

Price Match



* Required Fields