808022 Mono 2.5W Class D Audio Amplifier - PAM8302

Mono 2.5W Class D Audio Amplifier - PAM8302

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins.
Categories
Prices are VAT included
€4.97 Price
€4.07 + VAT

Qty
 

Details

This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps!

The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin  to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly.

Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Speaker is not included, use any 4 ohm or greater impedance speaker.

  • Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply
  • 50dB PSRR at 1KHz
  • Filterless design, with ferrite bead + capacitors on output.
  • Fixed 24dB gain, onboard trim potentiometer for adjusting input volume.
  • Thermal and short-circuit/over-current protection
  • Low current draw: 4mA quiescent and 1uA in shutdown mode

PAM8302A datasheet

Dimensions (without 0.1" header):

  • 15mm x 24mm x 2mm / 0.6" x 0.9" x 0.08"
  • Weight: 1.4g

Specifications

Part. No. : 2130

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on Mono 2.5W Class D Audio Amplifier - PAM8302

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.
  1. Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016 -

    807714 Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016 -

    A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is afalse
    Excl. Tax:
    €9.25
    Incl. Tax:
    €11.29
      Compare
  2. Stereo 20W Class D Audio Amplifier - MAX9744

    807895 Stereo 20W Class D Audio Amplifier - MAX9744

    This slim little board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Pfalse
    Excl. Tax:
    €18.50
    Incl. Tax:
    €22.57
      Compare

Price Match



* Required Fields