582507 2452 - ACS711EX Current Sensor Carrier -15.5A to +15.5A

2452 - ACS711EX Current Sensor Carrier -15.5A to +15.5A

This board is a simple carrier of Allegro’s ±15.5 A ACS711 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~0.6 mΩ) current path and electrical isolation up to 100 V. This version accepts a bidirectional current input with a magnitude up to 15.5 A and outputs a proportional analog voltage centered at Vcc/2 with a typical error of ±5%. It operates from 3 V to 5.5 V, so it can interface directly to both 3.3 V and 5 V systems.
Categorie
Prezzi IVA inclusa
€ 4,38 Prezzo
€ 3,59 + VAT

Qty
 

Dettagli

This current sensor is a carrier board or breakout board for Allegro’s ACS711KEXLT-15AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (551k pdf) before using this product. This sensor has an operating voltage of 3 V to 5.5 V and an output sensitivity of 90 mV/A when Vcc is 3.3 V (or 136 mV/A when Vcc is 5 V). The following list details some of the sensor’s key features:

  • Designed for bidirectional input current from -15.5 A to 15.5 A (though the robust sensor IC can tolerate 100 ms transient current spikes up to 100 A).
  • Conductive path internal resistance is typically 0.6 mΩ, and the PCB is made with 2-oz copper, so very little power is lost in the board.
  • Use of a Hall effect sensor means the IC is able to electrically isolate the current path from the sensor’s electronics (for applications up to 100 V), which allows the sensor to be inserted anywhere along the current path and to be used in applications that require electrical isolation.
  • 100 kHz bandwith.
  • Good accuracy and reliability: factory calibration results in a typical total output error of ±5% at room temperature, the output offset voltage is extremely stable, and the sensor has zero magnetic hysteresis.
  • Overcurrent FAULT output latches low when current magnitude exceeds 15.5 A.
  • Operating temperature range of -40°C to 125°C.

The pads are labeled on the bottom silkscreen, as shown in the picture to the right. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.

This 15.5 A current sensor is marked with a black X. We also sell a 31 A version that uses the same carrier PCB; you can distinguish the versions by reading the text on the IC or by looking at the color of the X on the bottom silkscreen.

This sensor is very similar to our original ACS711 -12.5 to +12.5 A Current Sensor Carrier, but uses a smaller “EX” package that has a larger optimized sensing range and reduced internal resistance. The board size, pinout, and hole locations are all unchanged, so it can generally be used as a drop-in replacement for our ACS711 carriers with “LC” packages.

Using the sensor

Electrical connections

The sensor requires a supply voltage of 3 V to 5.5 V to be connected across the Vcc and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is Vcc/2 and changes by 90 mV per amp of input current (when Vcc = 3.3 V), with positive current increasing the output voltage and negative current decreasing the output voltage. The relationship between the instantaneous input current, i, and sensor output voltage, VOUT, can be represented by the following equations:

 

 

The FAULT pin is normally high and latches low when the current exceeds ±15.5 A. Once the FAULT pin is latched low, the only way to reset it is by toggling power on the Vcc pin. In our tests, this module was able to handle 15 A of continuous current without exceeding 50°C, with no cooling beyond the heat dissipation of the PCB.

The input current can be connected to the board in a variety of ways. Holes with 0.1″, 3.5 mm, and 5 mm spacing are available as shown in the diagram above for connecting male header pins or terminal blocks. For high-current applications, you can solder wires directly to the through-holes that best match your wires, or you can use solderless ring terminal connectors, as shown in the picture above. The large through-holes are big enough for #6 screws.

Warning: This product is intended for use below 30 V. Working with higher voltages can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.

Mounting information

The board has two mounting holes on the logic side of the board. These mounting holes are 0.5" apart and are designed for #2 screws.

Specifiche

Part. No. : 2452

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2452 - ACS711EX Current Sensor Carrier -15.5A to +15.5A

Sort by Descending
  • 25/11/15 17.55 Devo usare il presente sensore e il sensore
    5825082453 - ACS711EX Current Sensor Carrier -31A to +31A
    con una tensione di 220 Volt
    vorrei sapere se ci sono problemi.
    Una volta eseguito il collegamento, il sensore e' nascosto nel quadro elettrico pertanto accessibile solo a personale autorizzato e competente
    grazie
    • Salve,
      prima di collegare qualsiasi cosa alla rete elettrica e' bene studiare a fondo il datasheet e la documentazione dei componenti. Questo sensore non e' idoneo ad essere collegato alla rete. Si suggerisce un modello a toroide aperto come il: 711005 e simili. Leggere sempre la documentazione! Grazie
    • Do you find this question helpful?  Si   No
Fai una domanda (Registrati oppure Esegui il Login ).
  1. SparkFun Low Current Sensor Breakout - ACS712

    708883 SparkFun Low Current Sensor Breakout - ACS712

    The ACS712 current sensor measures up to 5A of DC or AC current.
    Tasse escluse:
    € 8,98
    IVA inclusa:
    € 10,96
      Confronta
  2. 1187 - ACS714 Current Sensor Carrier -30 to +30A

    341187 1187 - ACS714 Current Sensor Carrier -30 to +30A

    Sensore di corrente basato sull' ACS714 della Allegro. Può misurare fino a 30A e fornisce in uscita una tensione analogica difalse
    Tasse escluse:
    € 6,68
    IVA inclusa:
    € 8,15
      Confronta
  3. 1185 - ACS714 Current Sensor Carrier -5 to +5A

    341185 1185 - ACS714 Current Sensor Carrier -5 to +5A

    Sensore di corrente basato sull' ACS714 della Allegro. Questo sensore è in grado di misurare correnti fino a 5A e fornisce infalse
    Tasse escluse:
    € 7,44
    IVA inclusa:
    € 9,08
      Confronta
  4. 2453 - ACS711EX Current Sensor Carrier -31A to +31A

    582508 2453 - ACS711EX Current Sensor Carrier -31A to +31A

    This board is a simple carrier of Allegro’s ±31 A ACS711 Hall effect-based linear current sensor with overcurrent fault outpufalse
    Tasse escluse:
    € 3,59
    IVA inclusa:
    € 4,38
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!