342826 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

This gearmotor is a powerful 12V brushed DC motor with a 102.083:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 6533 counts per revolution of the gearbox’s output shaft.
Categorie
Prezzi IVA inclusa
€ 39,53 Prezzo
€ 32,40 + VAT

 

Dettagli

This gearmotor is a powerful 12V brushed DC motor with a 102.083:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 6533 counts per revolution of the gearbox’s output shaft. These units have a 0.61"-long, 6 mm-diameter D-shaped output shaft. 

Key specs at 12 V: 100 RPM and 300 mA free-run, 220 oz-in (16 kg-cm) and 5 A stall.


This powerful brushed DC gearmotor is available in six different gear ratios and features an integrated quadrature encoder with 64 counts per revolution (CPR) of the motor shaft.
These motors are intended for use at 12 V, though in general, these kinds of motors can run at voltages above and below the nominal voltage (they can begin rotating at voltages as low as 1 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 11" (28 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our malejumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions:

ColorFunction
Red motor power (connects to one motor terminal)
Black motor power (connects to the other motor terminal)
Green encoder GND
Blue encoder Vcc (3.5 – 20 V)
Yellow encoder A output
White encoder B output

The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. 

Dimensions

Size: 37D x 72.5L mm1
Weight: 230 g
Shaft diameter: 6 mm

General specifications

Gear ratio: 100:1
Free-run speed @ 6V: 50 rpm2
Free-run current @ 6V: 250 mA2
Stall current @ 6V: 2500 mA2
Stall torque @ 6V: 110 oz·in2
Free-run speed @ 12V: 100 rpm
Free-run current @ 12V: 300 mA
Stall current @ 12V: 5000 mA
Stall torque @ 12V: 220 oz·in
Lead length: 11 in

Notes:

1 Length measurement does not include gearbox shaft or the raised area immediately around it.
2 This motor will run at 6 V but is intended for operation at 12 V.

Dimension diagram of the 37D mm Metal Gearmotor with 64 CPR Encoder (194k pdf)

Specifiche

Part. No. : 2826
Diam. Asse mm : 6

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

Sort by Descending
  • 08/07/20 13.15 non mi è chiaro se la velocità di 100rpm è riferita alla rotazione del motor shaft o al gearbox’s output shaft. Inoltre l'encoder misura la velocità del motor shaft o del gearbox’s output shaft?
    Grazie, Piero
    • Salve, la velocita' di 100 RPM e' riferita all'asse di uscita del motoriduttore (asse del riduttore). L'encoder e' posizionato sul retro del motore, e misura la velocita' del motore (per avere una risoluzione maggiore). Grazie
    • Do you find this question helpful?  Si   No
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Motoriduttore 12Vdc 81RPM Encoder

    420114 Motoriduttore 12Vdc 81RPM Encoder

    Motoriduttore: Tensione 12 Vdc Coppia 5.1 Kg/cm 81 RPM Diametro Asse 6 mm Encoder 3 impulsi / giro
    Tasse escluse:
    € 17,91
    IVA inclusa:
    € 21,85
      Confronta
  2. Motoriduttore 12Vdc 66RPM Encoder

    420115 Motoriduttore 12Vdc 66RPM Encoder

    Motoriduttore: Tensione 12 Vdc Coppia 6.12 Kg/cm 66 RPM Diametro Asse 6 mm Encoder 3 impulsi / giro
    Tasse escluse:
    € 17,91
    IVA inclusa:
    € 21,85
      Confronta
  3. Motoriduttore 12Vdc 33RPM Encoder

    420116 Motoriduttore 12Vdc 33RPM Encoder

    Motoriduttore: Tensione 12 Vdc Coppia 10.2 Kg/cm 33 RPM Diametro Asse 6 mm Encoder 3 impulsi / giro
    Tasse escluse:
    € 17,91
    IVA inclusa:
    € 21,85
      Confronta
  4. 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors

    582566 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors

    These aluminum gearmotor brackets let you mount Pololu’s 37D mm metal gearmotors to your project. The brackets are sold in pafalse
    Tasse escluse:
    € 6,50
    IVA inclusa:
    € 7,93
      Confronta
  5. 2827 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

    342827 2827 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

    This gearmotor is a powerful 12V brushed DC motor with a 131.25:1 metal gearbox and an integrated quadrature encoder that profalse
    Tasse escluse:
    € 34,54
    IVA inclusa:
    € 42,14
      Confronta
  6. 99:1 Metal Gearmotor 25Dx54L mm HP 6V with 48 CPR Encoder

    342276 99:1 Metal Gearmotor 25Dx54L mm HP 6V with 48 CPR Encoder

    This gearmotor consists of a high-power, 6 V brushed DC motor combined with a 98.78:1 metal spur gearbox, and it has an integfalse
    Tasse escluse:
    € 29,98
    IVA inclusa:
    € 36,58
      Confronta
  7. 4756 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder (Helical Pinion)

    344756 4756 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder (Helical Pinion)

    Motoriduttore 12V con encoder a quadratura ad alta risoluzione. Con ingranaggi helical, riducono il rumore ed aumentano l'efffalse
    Tasse escluse:
    € 34,54
    IVA inclusa:
    € 42,14
      Confronta
  8. 4887 - 99:1 Metal Gearmotor 25Dx69L mm LP 12V with 48 CPR Encoder

    344887 4887 - 99:1 Metal Gearmotor 25Dx69L mm LP 12V with 48 CPR Encoder

    Motoriduttore 12V con encoder a quadratura ad alta risoluzione. Motore a bassa potenza/consumo
    Tasse escluse:
    € 28,37
    IVA inclusa:
    € 34,61
      Confronta