501411 Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface -

Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface -

Shield Arduino compatibile con 16 uscite PWM, utilizza il chip PCA9685 e comunica tramite protocollo I2C, e' possibile pilotare piccoli carichi e servi RC. Gli headers per Arduino non sono inclusi.
Categorie
Prezzi IVA inclusa
€ 19,75 Prezzo
€ 16,19 + VAT

Qty
 

Dettagli

You want to make a cool Arduino robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that the Arduino has only a few PWM outputs, and maybe those outputs are conflicting with another shield! What now? You could give up OR you could just get our handy PWM and Servo driver shield. It's just like our popular PWM/Servo Breakout but now Arduino-ready and works with any Arduino that uses shields: Uno, Leo, Mega, ADK, its all good. 

When we saw this chip, we quickly realized what an excellent add-on this would be.Using only two I2C pins, control 16 free-running PWM outputs! You can even stack up 62 shields to control up to 992 PWM outputs (which we would really like to see since it would be glorious and like 4 feet tall) Because I2C is a shared bus you can also connect other I2C devices and sensors to the SCL/SDA pins as long as their addresses don't conflict (this shield has address 0x40)

  • There's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
  • It is 5V compliant, which means you can control it from a 3.3V Arduino and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
  • 6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
  • Adjustable frequency PWM up to about 1.6 KHz
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
  • Configurable push-pull or open-drain output

We wrapped up this lovely chip into a shield with a couple nice extras

  • Terminal block for power input (or you can use the 0.1" breakouts on the side)
  • Reverse polarity protection on the terminal block input
  • Green and red power-good LEDs
  • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
  • Stackable design. You'll need to pick up stacking headers and right angle 3x4 headers in order to stack on top of this shield without the servo connections getting in the way.
  • A spot to place a big capacitor on the V+ line (in case you need it)
  • 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
  • Solder jumpers for the 6 address select pins
  • A lot of extra space remaining? Let's turn it into a prototyping area. You get a 5x20 proto area for any extra wiring you'd like to add

This product comes with a fully tested and assembled shield as well as 4 pieces of 3x4 male straight header (for servo/LED plugs), a 2-pin terminal block (for power) and a stick of 0.1" header so you can plug into an Arduino. A little light soldering will be required to assemble and customize the board by attaching the desired headers but it is a 15 minute task that even a beginner can do. Servos and Arduino not included - but we do sell tons of different servos in the shop so pick up a few while you're here! 

Check out our tutorial with Arduino and you can get our documented Arduino library which has both PWM and Servo examples!

Dimensions (no headers or terminal block) 2.1" x 2.7" x 0.1" (54mm x 70mm x 3mm)

Adafruit 16-channel PWM/Servo Shield Tutorial
16 channels of servo-bustin' power

PCA9685 datasheet

Specifiche

Part. No. : 1411
Interfaccia : I2C
Tensione : 5
Tipo Shield : Ctrl Motori, Potenza, LED

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface -

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

    501815 Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

    Servo/PWM controller. Utilizza 2 pin del microcontrollore (I2C) per pilotare fino a 16 servi rc oppure qualsiasi utilizzatorefalse
    Tasse escluse:
    € 13,86
    IVA inclusa:
    € 16,91
      Confronta
  2. Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

    501429 Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

    Driver per controllare in PWM 24 canali separati, ottimo per pilotare display e LED, basato sul chip TLC5947 utilizza il protfalse
    Tasse escluse:
    € 13,86
    IVA inclusa:
    € 16,91
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!