501429 Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

Driver per controllare in PWM 24 canali separati, ottimo per pilotare display e LED, basato sul chip TLC5947 utilizza il protocollo SPI
Prezzi IVA inclusa
€ 16,91 Prezzo
€ 13,86 + VAT

Qty
 

Dettagli

For all of you out there who want to control 24 channels of PWM, we salute you! We also would like you to check out this breakout board for the TLC5947 PWM driver chip. This chip can control 24 separate channels of 12-bit PWM output. Designed (and ideal) for LED control, this board is not good for driving servos.

Only three "SPI" pins are required to send data (our Arduino library shows how to to use any digital microcontroller pins). Best of all, the design is completely chainable. As long as there's enough power for all the boards you can chain as many as you'd like, like a little trail of blue PCBs stretching out into the sunset. Each of the 24 output's is constant-current and open drain. You can drive multiple LEDs in series, with a V+ anode supply of up to 30V. If you want to drive something that requires a digital input, you must use a pullup resistor from the drive pin to your logic level to create the full waveform. 

One resistor is used to set the current for each of the outputs, the constant current means that the LED brightness doesn't vary if the power supply dips. We use a 3.3K resistor for about 15mA but you can solder a thru-hole resistor over it if you'd like to change that value. Check the TLC5947 datasheet for details on resistor-to-current values. 

We include a few extras to make this board easy to use: a durable 5V low-dropout regulator (with reverse polarity protection in case y'know, you plug it in backwards), a green power-good LED, four mounting holes and a current-set resistor. A bit of 0.1" header is also included so you can solder it on and plug into a breadboard. 

To use: Power V+ with 5-30VDC, and connect ground to the common ground. Then send 3-5V logic SPI data on DIN (data in), CLK (clock) and LAT (latch). If you'd like to quickly turn off all the outputs, drop the OE pin - it's pulled high by default. Our Arduino library will get you started with blinking LEDs, install it and run the example code with the noted pin configuration.

  • Dimensions: 25.39mm / 0.9" x 51.1mm / 2" x 4mm / 0.1"
  • Weight: 4.76g

TLC5947 datasheet

Specifiche

Part. No. : 1429

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit 24-Channel 12-bit PWM LED Driver - SPI Interface - TLC5947

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

    501815 Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685

    Servo/PWM controller. Utilizza 2 pin del microcontrollore (I2C) per pilotare fino a 16 servi rc oppure qualsiasi utilizzatorefalse
    Tasse escluse:
    € 13,86
    IVA inclusa:
    € 16,91
      Confronta
  2. Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface -

    501411 Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface -

    Shield Arduino compatibile con 16 uscite PWM, utilizza il chip PCA9685 e comunica tramite protocollo I2C, e' possibile pilotafalse
    Tasse escluse:
    € 16,19
    IVA inclusa:
    € 19,75
      Confronta
  3. Adafruit 12-Channel 16-bit PWM LED Driver - SPI Interface - TLC59711

    501455 Adafruit 12-Channel 16-bit PWM LED Driver - SPI Interface - TLC59711

    Driver di potenza PWM a 16 bit, gestisce 12 LED. Interfaccia SPI, libreria Arduino disponibile.
    Tasse escluse:
    € 6,94
    IVA inclusa:
    € 8,47
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!