808845 Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board

Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board

Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driver chip is a nice alternative to the TB6612 driver.
Categorie
Prezzi IVA inclusa
€ 6,67 Prezzo
€ 5,47 + VAT

 

Dettagli

Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driver chip is a nice alternative to the TB6612 driver. Like that chip, you get 2 full H-bridges, but this chip is better for low voltage uses (can run from 2.7V up to 10.8V motor power) and has built in current limiting capability. We set it up for 1A current limiting so you don't get more than 2A per chip, but you can also disable the current limiting, or change it to a different limit!

We solder on DRV8833 onto a breakout board for you here, with a polarity protection FET on the motor voltage input. Each breakout chip contains two full H-bridges (four half H-bridges). That means you can drive two DC motors bi-directionally, or one stepper motor. Just make sure they're good for about 1.2 Amp or less of current, since that's the limit of this chip. They do handle a peak of 2A but that's just for a short amount of time, if you turn off the current limiting we set. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver! You also don't have to worry as much about burning out the chip with overdriving since there is current limiting.

There's two digital inputs per H-bridge (one for each half of the bridge), you can PWM one of the inputs to control motor speed. Runs at 2.7V-10.8V logic/motor power. The motor voltage is the same as the logic voltage, but logic voltage from 2.7V or greater will work so no need to worry if you are powering the motors from 9V and using 3.3V logic. For higher voltages, check out the TB6612. For much higher voltages and currents check out the DRV8871!

Comes as one assembled and tested breakout plus a small strip of header. You'll need to do some light soldering to attach the header onto the breakout PCB. Arduino, motors, and power supply not included.

  • Size: 26mm x 18mm x 3mm / 1.0" x 0.7" x 0.1"
  • Weight: 1.5g

Datasheets, PCB CAD files, diagrams, Fritzing object and more in the tutorial

Specifiche

Part. No. : 3297

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. MiniMoto - DRV8830 Breakout

    711890 MiniMoto - DRV8830 Breakout

    Motor Controller basato sul Chip DRV8830, controlla un Motore a spazzole, con tensione da 2,7V a 6,8V e 1A di potenza max. Sifalse
    Tasse escluse:
    € 8,20
    IVA inclusa:
    € 10,00
      Confronta
  2. 2130 - DRV8833 Dual Motor Driver Carrier

    807831 2130 - DRV8833 Dual Motor Driver Carrier

    This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair ofalse
    Tasse escluse:
    € 4,47
    IVA inclusa:
    € 5,45
      Confronta
  3. 2135 - DRV8835 Dual Motor Driver Carrier

    807832 2135 - DRV8835 Dual Motor Driver Carrier

    This tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pairfalse
    Tasse escluse:
    € 4,44
    IVA inclusa:
    € 5,42
      Confronta
  4. 2990 - DRV8838 Single Brushed DC Motor Driver Carrier

    342990 2990 - DRV8838 Single Brushed DC Motor Driver Carrier

    This tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor.
    Tasse escluse:
    € 3,50
    IVA inclusa:
    € 4,27
      Confronta
  5. TB6600 Stepper Motor Driver

    120043 TB6600 Stepper Motor Driver

    TB6600 arduino is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is comfalse
    Tasse escluse:
    € 16,16
    IVA inclusa:
    € 19,72
      Confronta