808588 Adafruit Feather 32u4 Basic Proto

Adafruit Feather 32u4 Basic Proto

This is the Feather 32u4 Basic Proto, it has a bunch of prototyping space built right in
Prezzi IVA inclusa
€ 25,99 Prezzo
€ 21,30 + VAT

 

Dettagli

This is the Feather 32u4 Basic Proto, it has a bunch of prototyping space built right in We have other boards in the Feather family, check'em out here!

At the Feather 32u4's heart is at ATmega32u4 clocked at 8 MHz and at 3.3V logic, a chip setup we've had tons of experience with as it's the same as the Flora. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. This chip is well supported in the Arduino IDE and can run just about every sensor/library out there.

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.

Here's some handy specs!

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 4.8 grams
  • ATmega32u4 @ 8MHz with 3.3V logic/power
  • 3.3V regulator with 500mA peak current output
  • USB native support, comes with USB bootloader and serial port debugging
  • You also get tons of pins - 20 GPIO pins
  • Hardware Serial, hardware I2C, hardware SPI support
  • 8 x PWM pins
  • 10 x analog inputs (one is used to measure the battery voltage)
  • Built in 100mA lipoly charger with charging status indicator LED
  • Pin #13 red LED for general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

The Feather 32u4 Basic Proto has some extra space left over, so we give you a tiny little prototyping area. If you just need to attach a button or sensor, you may be able to skip out on a breadboard and wire it directly on there.

Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)

Check out our tutorial for all sorts of details, including schematics, files, IDE instructions, and more!

  • 51mm x 23mm x 8mm / 2.0" x 0.9" x 0.28"
  • Weight: 4.8g

 

Specifiche

Part. No. : 2771

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit Feather 32u4 Basic Proto

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Adafruit Feather 32u4 Bluefruit LE

    808524 Adafruit Feather 32u4 Bluefruit LE

    This is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with builfalse
    Tasse escluse:
    € 31,84
    IVA inclusa:
    € 38,84
      Confronta
  2. FeatherWing Proto - Prototyping Add-on For All Feather Boards

    808529 FeatherWing Proto - Prototyping Add-on For All Feather Boards

    This is the FeatherWing Proto - a prototyping add-on for all Feather boards.
    Tasse escluse:
    € 5,47
    IVA inclusa:
    € 6,67
      Confronta
  3. Adafruit Feather 32u4 Adalogger

    808553 Adafruit Feather 32u4 Adalogger

    This is the Adafruit Feather 32u4 Adalogger - our take on an 'all-in-one' datalogger (or data-reader) with built in USB and bfalse
    Tasse escluse:
    € 20,52
    IVA inclusa:
    € 25,03
      Confronta
  4. Feather Stacking Headers - 12-pin and 16-pin female headers

    808554 Feather Stacking Headers - 12-pin and 16-pin female headers

    These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!
    Tasse escluse:
    € 1,79
    IVA inclusa:
    € 2,18
      Confronta
  5. 8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards

    808581 8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards

    This is the 8-Channel PWM or Servo​ FeatherWing, you can add 8 x 12-bit PWM outputs to your FeatherWing.
    Tasse escluse:
    € 9,44
    IVA inclusa:
    € 11,52
      Confronta
  6. OLED Breakout Board - 16-bit Color 1.5" w/microSD holder

    808884 OLED Breakout Board - 16-bit Color 1.5" w/microSD holder

    This OLED uses the SSD1351 driver chip, which manages the display. You can talk to the driver chip using 4-wire write-only SPfalse
    Tasse escluse:
    € 37,17
    IVA inclusa:
    € 45,35
      Confronta
  7. Adafruit AMG8833 IR Thermal Camera FeatherWing

    809083 Adafruit AMG8833 IR Thermal Camera FeatherWing

    This is the Thermal Camera FeatherWing: thanks to the Panasonic AMG8833 8x8 GridEYE sensor, it adds heat-vision to any Feathefalse
    Tasse escluse:
    € 44,80
    IVA inclusa:
    € 54,66
      Confronta
  8. Adafruit DotStar FeatherWing - 6 x 12 RGB LEDs

    809084 Adafruit DotStar FeatherWing - 6 x 12 RGB LEDs

    This is the DotStar FeatherWing, a 6x12 RGB LED Add-on For All Feather Boards!
    Tasse escluse:
    € 31,84
    IVA inclusa:
    € 38,84
      Confronta