501789 Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras

Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras

Il PN532 e' il piu' diffuso chip NFC, e' quello che si trova nella maggior parte dei telefoni o dispositivi che utilizzano l'NFC. Ora in formato Shield per Arduino.
Prezzi IVA inclusa
€ 45,13 Prezzo
€ 36,99 + VAT

Qty
 

Dettagli

We've taken our popular Adafruit PN532 breakout board and turned it into a shield - the perfect tool for any 13.56MHz RFID or NFC application. The Adafruit NFC shield uses the PN532 chip-set (the most popular NFC chip on the market) and is what is embedded in pretty much every phone or device that does NFC. It can pretty much do it all, such as read and write to tags and cards, communicate with phones (say for payment processing), and 'act' like a NFC tag. If you want to do any sort of embedded NFC work, this is the chip you'll want to use! 

NFC (Near Field Communications) is a way for two devices very close to each other to communicate. Sort of like a very short range bluetooth that doesn't require authentication. It is an extension of RFID, so anything you can do with RFID you can do with NFC. You can do more stuff with NFC as well, such as communicate bi-directionally with cell phones 

Because it can read and write tags, you can always just use this for RFID-tag projects. We carry a few different tags that work great with this chip. It can also work with any other NFC/RFID Type 1 thru 4 tag (and of course all the other NXP MiFare type tags) 

The Adafruit shield was designed by RF engineers using the best test equipment to create a layout and antenna with 10cm (4 inch) range, the maximum range possible using the 13.56MHz technology. You can easily attach the shield behind a plastic plate with standoffs and still read cards through a (non-metal) barrier. 

This shield is designed to use I2C or SPI communication protocols. I2C is the default, as it uses fewer pins: analog 4 and 5 are used for I2C (of course you can still connect other I2C devices to the bus). Digital #2 is used for "interrupt" notification. This means you don't have to sit there and 'poll' the chip to ask if a target tag has been found, the pin will pull low when a card, phone, etc is within range. You can adjust which pin is used if you need to keep digital #2 for something else. It is also easy to change the shield over to SPI where you can use any 4 digital pins by shorting two solder jumpers on the top of the PCB. Compatible with any "classic" Arduino - NG, Diecimilla, Duemilanove, UNO - as well as Mega R3 or later. For using the I2C interface with Mega R2 or earlier, two wires must be soldered as the I2C pins are in a different location on earlier Megas. 

Comes with: the Adafruit NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna, 36-pin 0.1" header for attaching the shield to an Arduino. We also toss in a Mifare Classic 1K card!

Check out our RFID/NFC project page for documentation, libraries, and other support

Specifiche

Part. No. : 789
Tipo Shield : Wireless

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit PN532 NFC/RFID Controller Shield for Arduino + Extras

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. PN532 NFC/RFID controller breakout board - v1.3

    501364 PN532 NFC/RFID controller breakout board - v1.3

    Il PN532 e' il piu' diffuso chip NFC, e' quello che si trova nella maggior parte dei telefoni o dispositivi che utilizzano l'NFC.
    Tasse escluse:
    € 36,99
    IVA inclusa:
    € 45,13
      Confronta
  2. MiFare Classic (13.56MHz RFID/NFC) Charm - 1KB

    501884 MiFare Classic (13.56MHz RFID/NFC) Charm - 1KB

    Tag MiFare effetto "porcellana". Basata su chip NXP S50.
    Tasse escluse:
    € 2,57
    IVA inclusa:
    € 3,14
      Confronta
  3. NFC Shield V2.0

    115069 NFC Shield V2.0

    Shield NFC (Near Field Communication), con transceiver PN532 che gestisce le comunicazioni a 13.56MHz
    Tasse escluse:
    € 28,29
    IVA inclusa:
    € 34,51
    A partire da:
    € 21,90
      Confronta
  4. Starter Shield EN(Tick Tock shield)

    115070 Starter Shield EN(Tick Tock shield)

    Shield ideale per i neofiti. E' corredato da pulsanti, buzzer, sensori, display, etc. Consente molte sperimentazioni e puo' efalse
    Tasse escluse:
    € 13,02
    IVA inclusa:
    € 15,88
    A partire da:
    € 9,52
      Confronta
  5. Grove - NFC Tag

    807917 Grove - NFC Tag

    Grove - NFC Tag is a highly integrated Near Field Communication Tag module,this module is I2C interface,which base on M24LR64false
    Tasse escluse:
    € 20,41
    IVA inclusa:
    € 24,90
      Confronta
  6. RS232 Shield

    807918 RS232 Shield

    RS232 Shield is a standard communication port for industry equipment.This module is base on MAX232,which is a dual driver/recfalse
    Tasse escluse:
    € 11,65
    IVA inclusa:
    € 14,21
      Confronta
  7. HydraNFC Shield and HydraNFC Antenna

    808068 HydraNFC Shield and HydraNFC Antenna

    The HydraNFC is a NFC shield hardware to sniff, read/write or emulate any 13.56MHz NFC tags (with the help of direct modes) ffalse
    Tasse escluse:
    € 82,20
    IVA inclusa:
    € 100,28
      Confronta
  8. DSLR Universal Interval IR Remote

    808071 DSLR Universal Interval IR Remote

    With "DSLR Universal Interval IR Remote", your digital SLR camera can be used to shoot Time-lapse movies. The remotfalse
    Tasse escluse:
    € 27,40
    IVA inclusa:
    € 33,43
      Confronta
  9. MiFare Classic (13.56MHz RFID/NFC) Card - 1KB

    808140 MiFare Classic (13.56MHz RFID/NFC) Card - 1KB

    These can be read by almost any 13.56MHz RFID/NFC reader but make sure it can handle MiFare cards as there are a few other enfalse
    Tasse escluse:
    € 2,57
    IVA inclusa:
    € 3,14
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!