808282 Arduino 9 Axes Motion Shield

Arduino 9 Axes Motion Shield

The BNO055 is a System in Package (SiP), integrating a triaxial 14-bit accelerometer, a triaxial 16-bit gyroscope with a range of ±2000 degrees per second, a triaxial geomagnetic sensor and a 32-bit microcontroller running the BSX3.0 FusionLib software.
Categorie
Prezzi IVA inclusa
€ 28,67 Prezzo
€ 23,50 + VAT

 

Dettagli

The Arduino 9 Axes Motion Shield is based on the BNO055 absolute orientation sensor (datasheet) from Bosch Sensortec GmbH. 
The BNO055 is a System in Package (SiP), integrating a triaxial 14-bit accelerometer, a triaxial 16-bit gyroscope with a range of ±2000 degrees per second, a triaxial geomagnetic sensor and a 32-bit microcontroller running the BSX3.0 FusionLib software. 
The sensor features three-dimensional acceleration, yaw rate and magnetic field strength data each in 3 perpendicular axes. 
 
It also provides the sensor fusion signals such as 
  • Quaternion
  • Euler angles
  • Rotation vector
  • Linear acceleration
  • Gravity vector
In addition, it incorporates an intelligent interrupt engine, which allows for triggering interrupts based on
  • slow or no motion recognition
  • any motion (slope) detection 
  • high-g-detection.
The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
 
 

Summary

 
Operating Voltage          5V
Power Consumption      50mW  
 

Schematic & Reference Design 

 

Power

 
The Arduino 9 Axes Motion Shield has no power jack and is powered only when attached to an Arduino board.
 
 
 

Input and Output

 
  The shield features several TinkerKit input/output and communication interfaces. Connecting TinkerKit modules can simplify the creation of a project or a prototype.  The on-board connectors are :
  • 2 TinkerKit Inputs: IN2 and IN3 (in white), these connectors are routed to the Arduino A2 and A3 analog input pins.
  • 2 TinkerKit Outputs: OUT5 and OUT6 (in orange), these connectors are routed to the Arduino PWM outputs on pins 5 and 6.
  • 2 TinkerKit TWI: these connectors (4-pin in white) are routed on the Arduino TWI interface. Both connect to the same TWI interface to allow you to create a chain of TWI devices.

 Physical Characteristics


 The maximum length and width of the 9 Axes Motion Shield PCB are 2.7 and 2.1 inches respectively. Four screw holes allow the board to be attached to a surface or case. Note that the distance between digital pins 7 and 8 is 160 mil (0.16"), not an even multiple of the 100 mil spacing of the other pins.

 Compatibility

The Arduino 9 Axes Motion Shield is compatible with Uno, Yùn, Leonardo, Ethernet, Mega and Due boards. When using the Arduino 9 Axes Motion Shield, be sure to solder the Interrupt bridge and Reset bridge in the correct position depending on the board used. See table:
 
BOARD INTERRUPT PIN RESET PIN
Arduino Uno D2 D4
Arduino Leonardo D7 D4
Arduino Yun D7 D4
Arduino Ethernet D2 D4
Arduino Due D2 D4
Arduino Mega D2 D4
  For example to use 9 Axes Motion Shield with ArduinoUNO solder the Interrupt bridge on the pin D2.
     


Programming
The 9 Axes Motion Shield can be programmed with the Arduino software (download).

In the Arduino IDE you will find the following examples, go to File -> Examples of Arduino IDE, under NAxesMotion, there are 4 sketches for the use of 9 Axes Motion Shield:

  • Accelerometer
    Example code to stream Accelerometer data
  • BareMinimum
    Example code to describe the Bare Minimum
  • Euler
    Example code to stream Euler data
  • Motion
    Example code of a game to demonstrate the Any motion and No motion Interrupt features
 
 

Conformity Declaration

Specifiche

Part. No. : A000070
Interfaccia : I/O
Tensione : 5
Tipo Shield : Sensori

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Arduino 9 Axes Motion Shield

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Grove - 3-Axis Digital Accelerometer(±400g)

    807914 Grove - 3-Axis Digital Accelerometer(±400g)

    The H3LIS331DL is a low power high performance 3-axis linear accelerometer belonging to the “nano” family, with digital I2C sfalse
    Tasse escluse:
    € 26,37
    IVA inclusa:
    € 32,17
      Confronta
  2. Grove - 3-Axis Digital Gyro

    808083 Grove - 3-Axis Digital Gyro

    Grove - 3-axis Gyro module based on ITG 3200. It is the world’s first single-chip, digital-output, 3-axis MEMS motion processfalse
    Tasse escluse:
    € 19,04
    IVA inclusa:
    € 23,23
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!