582563 DRV8824 Stepper Motor Driver Carrier, Low Current

DRV8824 Stepper Motor Driver Carrier, Low Current

Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 0.75A per fase, fino a 1.2A con dissipatore (non fornito). Eccezionale gestione microstep.
Prezzi IVA inclusa
€ 7,44 Prezzo
€ 6,10 + VAT

Qty
 

Dettagli

The DRV8824 stepper motor driver carrier is a breakout board for TI’s DRV8824 microstepping bipolar stepper motor driver, a lower-current version of the DRV8825. The DRV8824 carrier can only deliver up to 0.75 A per coil without a heat sink (it is rated for up to 1.2 A per coil with sufficient additional cooling), but it has larger current-sense resistors that allow for improved microstepping performance at low currents. This carrier has the same pinout, interface, and features as ourDRV8825 carrier, which means it can serve as a direct substitute for the DRV8825 carrier when using lower-current stepper motors.

This product is a carrier board or breakout board for TI’s DRV8824 stepper motor driver; we therefore recommend careful reading of the DRV8824 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 1.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features:

  • Simple step and direction control interface
  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
  • 45 V maximum supply voltage
  • Built-in regulator (no external logic voltage supply needed)
  • Can interface directly with 3.3 V and 5 V systems
  • Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
  • Short-to-ground and shorted-load protection
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB
  • Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)

We also carry a DRV8825 stepper motor driver carrier that can serve as a direct, higher-power substitute for the DRV8824 carrier. The DRV8825 can deliver up to 1.5 A per coil without a heat sink (2.2 A max with sufficient additional cooling). The only way to tell our DRV8824 carrier apart from the DRV8825 carrier is by the markings on the driver IC; if you have a mix of the two, you might consider marking them (there is a blank square on the bottom silkscreen you can use for this). 

This product ships with all surface-mount components—including the DRV8824 driver IC—installed as shown in the product picture.

Unipolar motors with five leads cannot be used with this driver.

Included hardware

The DRV8824 stepper motor driver carrier ships with one 1×16-pin breakaway 0.1" male header. The headers can be soldered in for use with solderless breadboards or 0.1" female connectors. You can also solder your motor leads and other connections directly to the board.

Dimensions

Size: 0.6″ × 0.8″
Weight: 1.6 g1

General specifications

Minimum operating voltage: 8.2 V
Maximum operating voltage: 45 V
Continuous current per phase: 0.75 A2
Maximum current per phase: 1.2 A3
Minimum logic voltage: 2.5 V4
Maximum logic voltage: 5.25 V4
Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32
Reverse voltage protection?: N

Notes:

1 Without included optional headers.
2 Without a heat sink or forced air flow.
3 With sufficient additional cooling.
4 This driver does works with 2.5 to 5.25 V logic. It does not take an external logic power supply.

Texas Instruments DRV8824 stepper motor driver datasheet (1MB pdf)
DRV8824/DRV8825 stepper motor driver carrier schematic diagram (196k pdf)

Specifiche

Part. No. : 2131

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on DRV8824 Stepper Motor Driver Carrier, Low Current

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

    582133 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

    Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 1.5A per fase, fino a 2.2A con dissipatore (nfalse
    Tasse escluse:
    € 6,66
    IVA inclusa:
    € 8,13
      Confronta
  2. BB-A4983 - TWO CHANNEL STEPPER MOTOR DRIVER

    502260 BB-A4983 - TWO CHANNEL STEPPER MOTOR DRIVER

    A4983 driver can control stepper motors and have two channels. The board can also power gear motors. It might be supplied by false
    Tasse escluse:
    € 9,00
    IVA inclusa:
    € 10,98
      Confronta
  3. BB-VNH3SP30 - VNH3SP30 FULL BRIDGE DRIVER

    502261 BB-VNH3SP30 - VNH3SP30 FULL BRIDGE DRIVER

    BB-VNH3SP30 is full bridge driver with up to 30A and 36V working voltage. It is good to drive Gear Robot motors with reversalfalse
    Tasse escluse:
    € 9,00
    IVA inclusa:
    € 10,98
      Confronta
  4. 2128 - A4988 Stepper Motor Driver Carrier, Black Edition

    342128 2128 - A4988 Stepper Motor Driver Carrier, Black Edition

    This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrefalse
    Tasse escluse:
    € 6,10
    IVA inclusa:
    € 7,44
      Confronta
  5. 1182 - A4988 Stepper Motor Driver Carrier

    341182 1182 - A4988 Stepper Motor Driver Carrier

    This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrefalse
    Tasse escluse:
    € 4,74
    IVA inclusa:
    € 5,78
      Confronta
  6. 2970 - AMIS-30543 Stepper Motor Driver Carrier

    342970 2970 - AMIS-30543 Stepper Motor Driver Carrier

    This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjfalse
    Tasse escluse:
    € 16,27
    IVA inclusa:
    € 19,85
      Confronta
  7. 2971 - DRV8880 Stepper Motor Driver Carrier

    342971 2971 - DRV8880 Stepper Motor Driver Carrier

    This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurfalse
    Tasse escluse:
    € 5,55
    IVA inclusa:
    € 6,77
      Confronta
  8. EasyDriver Stepper Motor Driver

    712779 EasyDriver Stepper Motor Driver

    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or false
    Tasse escluse:
    € 9,63
    IVA inclusa:
    € 11,75
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!