501164 INA169 Analog DC Current Sensor Breakout - 60V 5A Max

INA169 Analog DC Current Sensor Breakout - 60V 5A Max

Sensore di corrente continua, 60V 5 A max
Categorie
Prezzi IVA inclusa
€ 11,29 Prezzo
€ 9,25 + VAT

Qty
 

Dettagli

This breakout board will solve all your current-monitoring problems. Instead of struggling with a multimeter, you can just use the handy INA169 chip on this breakout to both measure both the DC current draw and have a handy analog output that is with respect to ground. The analog output makes this an ideal breakout for feedback-loop control. 

Most current-measuring devices such as our current panel meter are only good for low side measuring. That means that unless you want to get a battery involved, you have to stick the measurement resistor between the target ground and true ground. This can cause problems with circuits since electronics tend to not like it when the ground references change and move with varying current draw. This chip is much smarter - it can handle high side current measuring, up to +60VDC! 

A precision amplifier measures the voltage across the 0.1 ohm, 1% sense resistor. The resistor is rated for 2W continuous so you can measure up to +5A continuous. The output is a current that is drawn through the on-board 10K resistor so that the output voltage is 1V per Amp. So for 2A draw, the output will be 2V. You can change out the load resistor to be larger or smaller by cutting the traces next to it and soldering a thru hole resistor over. If you solder in a 20K resistor you'll get 2V per Amp, with a 5K resistor, 0.5V per Amp. 

We include a 6-pin header (so you can easily attach this sensor to a breadboard) as well as a 3.5mm terminal plug so you can easily attach and detach your load. Usage is simple. Power the sensor with 2.7-60V, and connect V+ to the high side of your power supply, then connect V- to your grounded load. Then use a multimeter to measure the voltage output, that's it!

Specifiche

Part. No. : 1164

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on INA169 Analog DC Current Sensor Breakout - 60V 5A Max

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. 1122 - 30 Amp Current Sensor AC&DC

    191122 1122 - 30 Amp Current Sensor AC&DC

    Il sensore misura correnti AC fino a 30A e correnti DC da -30A a +30A. L'uscita duale consente la misura di entrambe le compofalse
    Tasse escluse:
    € 33,93
    IVA inclusa:
    € 41,39
      Confronta
  2. ACS712 Current Sensor Breakout

    708882 ACS712 Current Sensor Breakout

    This is a breakout board for the fully integrated Hall Effect based linear ACS712 current sensor. The sensor gives precise cufalse
    Tasse escluse:
    € 6,41
    IVA inclusa:
    € 7,82
      Confronta
  3. 1185 - ACS714 Current Sensor Carrier -5 to +5A

    341185 1185 - ACS714 Current Sensor Carrier -5 to +5A

    Sensore di corrente basato sull' ACS714 della Allegro. Questo sensore è in grado di misurare correnti fino a 5A e fornisce infalse
    Tasse escluse:
    € 7,44
    IVA inclusa:
    € 9,08
      Confronta
  4. Non-Invasive Current Sensor - 30A

    711005 Non-Invasive Current Sensor - 30A

    Sensore di corrente non invasivo. E' costituito da un trasformatore con costruzione a "clip": si apre e si agganciafalse
    Tasse escluse:
    € 9,63
    IVA inclusa:
    € 11,75
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!