807832 2135 - DRV8835 Dual Motor Driver Carrier

2135 - DRV8835 Dual Motor Driver Carrier

This tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pair of DC motors, and it supports two possible control interfaces for added flexibility of use: IN/IN and PHASE/ENABLE. Operating voltage range from 2 to 11 V
Categorie
Prezzi IVA inclusa
€ 5,42 Prezzo
€ 4,44 + VAT

 

Dettagli

This tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pair of DC motors, and it supports two possible control interfaces for added flexibility of use: IN/IN and PHASE/ENABLE. With an operating voltage range from 2 to 11 V and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature, this driver is a great solution for powering up to two small, low-voltage motors. The carrier board has the form factor of a 14-pin DIP package, which makes it easy to use with standard solderless breadboards and 0.1″ perfboards.

Texas Instruments’ DRV8835 is a tiny dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2 to 11 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 1.5 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. The DRV8835 is a great IC, but its small, leadless package makes it difficult for the typical student or hobbyist to use; our breakout board gives this driver the form factor of a 14-pin DIP package, which makes it easy to use with standard solderless breadboards and 0.1″ perfboards. Since this board is a carrier for the DRV8835, we recommend careful reading of the DRV8835 datasheet (208k pdf). The board ships populated with SMD components, including the DRV8835, and adds a FET for reverse battery protection.

This board is very similar to our DRV8833 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1″ smaller in each dimension. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.

 

Features

  • Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
  • Motor supply voltage: 2–11 V
  • Logic supply voltage: 2–7 V
  • Output current: 1.2 A continuous (1.5 A peak) per motor
  • Motor outputs can be paralleled to deliver 2.4 A continuous (3 A peak) to a single motor
  • Two possible interface modes: IN/IN (outputs mostly mirror inputs) or PHASE/ENABLE (one pin for direction and another for speed)
  • Inputs are 3V- and 5V-compatible
  • Under-voltage lockout and protection against over-current and over-temperature
  • Reverse-voltage protection on the motor supply
  • Compact size (0.7″×0.4″) with the form factor of a 14-pin DIP package



Motor and motor power connections are made on one side of the board and logic power and control connections are made on the other. Each control input is pulled low through a weak pull-down resistor (approximately 100 kΩ), so the driver will be in the IN/IN mode if the MODE pin is left disconnected, and the driver outputs will be disabled by default. The driver requires a motor voltage between 2 and 11 V and a logic voltage between 2 and 7 V; the logic voltage can typically be supplied by or shared with the controlling device.

The DRV8835 features two possible control modes: IN/IN and PHASE/ENABLE. The MODE pin determines the control interface. Setting the MODE pin high, either with a pull-up resistor or a driving-high I/O line, sets the driver to PHASE/ENABLE mode, where the PHASE pin determines the motor direction and the ENABLE pin can be supplied with a PWM signal to control the motor speed. This mode is generally easier to use as it only requires one PWM per channel, but it only allows for drive/brake operation. (Drive/brake operation usually provides a more linear relationship between PWM duty cycle and motor speed than drive/coast operation, and we generally recommend using drive/brake operation when possible.)

Dimensions

Size:

0.4″ × 0.7″1

Weight:

0.5 g1

General specifications

Motor driver:

DRV8835

Motor channels:

2

Minimum operating voltage:

2.0 V

Maximum operating voltage:

11 V

Continuous output current per channel:

1.2 A2

Peak output current per channel:

1.5 A

Continuous paralleled output current:

2.4 A2

Reverse voltage protection?:

Y

Notes:

Without included hardware.

Typical results with 100% duty cycle at room temperature.

Specifiche

Part. No. : 2135

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2135 - DRV8835 Dual Motor Driver Carrier

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Motor Driver 1A Dual TB6612FNG

    709457 Motor Driver 1A Dual TB6612FNG

    Modulo per controllare due motori DC fino a 1.2A.
    Tasse escluse:
    € 6,87
    IVA inclusa:
    € 8,38
      Confronta
  2. MiniMoto - DRV8830 Breakout

    711890 MiniMoto - DRV8830 Breakout

    Motor Controller basato sul Chip DRV8830, controlla un Motore a spazzole, con tensione da 2,7V a 6,8V e 1A di potenza max. Sifalse
    Tasse escluse:
    € 8,20
    IVA inclusa:
    € 10,00
      Confronta
  3. 2130 - DRV8833 Dual Motor Driver Carrier

    807831 2130 - DRV8833 Dual Motor Driver Carrier

    This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair ofalse
    Tasse escluse:
    € 4,47
    IVA inclusa:
    € 5,45
      Confronta
  4. 713 - TB6612FNG Dual Motor Driver Carrier

    807833 713 - TB6612FNG Dual Motor Driver Carrier

    This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectionafalse
    Tasse escluse:
    € 4,47
    IVA inclusa:
    € 5,45
      Confronta
  5. 2137 - A4990 Dual Motor Driver Carrier

    807834 2137 - A4990 Dual Motor Driver Carrier

    This compact breakout board makes it easy to use Allegro’s A4990 dual motor driver, which can control two bidirectional DC mofalse
    Tasse escluse:
    € 7,90
    IVA inclusa:
    € 9,64
      Confronta
  6. 2990 - DRV8838 Single Brushed DC Motor Driver Carrier

    342990 2990 - DRV8838 Single Brushed DC Motor Driver Carrier

    This tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor.
    Tasse escluse:
    € 3,50
    IVA inclusa:
    € 4,27
      Confronta
  7. 2753 - Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+

    342753 2753 - Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+

    This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+ and provides an easy and low-cost solutfalse
    Tasse escluse:
    € 6,68
    IVA inclusa:
    € 8,15
      Confronta
  8. Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max

    808734 Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max

    This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. In particular, the simple false
    Tasse escluse:
    € 8,16
    IVA inclusa:
    € 9,96
      Confronta
  9. Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board

    808845 Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board

    Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driverfalse
    Tasse escluse:
    € 5,47
    IVA inclusa:
    € 6,67
      Confronta