711977 Triple-Axis Digital-Output Gyro ITG-3200 Breakout

Triple-Axis Digital-Output Gyro ITG-3200 Breakout

Accelerometro a tre assi basato sul sensore ITG-3200, uscita digitale su protocollo I2C
Categorie
Prezzi IVA inclusa
€ 24,55 Prezzo
€ 20,12 + VAT

Qty
 

Dettagli

This is a breakout board for InvenSense's ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for digitizing the gyro outputs, a user-selectable internal low-pass filter bandwidth, and a Fast-Mode I2C (400kHz) interface. Additional features include an embedded temperature sensor and a 2% accurate internal oscillator.

The ITG-3200 can be powered at anywhere between 2.1 and 3.6V. For power supply flexibility, the ITG-3200 has a separate VLOGIC reference pin (labeled VIO), in addition to its analog supply pin (VDD) which sets the logic levels of its serial interface. The VLOGIC voltage may be anywhere from 1.71V min to VDD max. For general use, VLOGIC can be tied to VCC. The normal operating current of the sensor is just 6.5mA.

Communication with the ITG-3200 is achieved over a two-wire (I2C) interface. The sensor also features a interrupt output, and an optional clock input. A jumper on the top of the board allows you to easily select the I2C address, by pulling the AD0 pin to either VCC or GND; the board is shipped with this jumper tied to VCC. If you don't plan on using the CLKIN pin, you can short the jumper on the bottom of the board to tie it to GND.

This breakout board is shipped as shown in the images. Note that there are two unpopulated resistors on the I2C lines, these can be added later by the customer if desired.

Features:

  • Digital-output X-, Y-, and Z-Axis angular rate sensors (gyros) on one integrated circuit
  • Digitally-programmable low-pass filter
  • Low 6.5mA operating current consumption for long battery life
  • Wide VDD supply voltage range of 2.1V to 3.6V
  • Standby current: 5μA
  • Digital-output temperature sensor
  • Fast Mode I2C (400kHz) serial interface
  • Optional external clock inputs of 32.768kHz or 19.2MHz to synchronize with system clock
  • Pins broken out to a breadboard friendly 7-pin 0.1" pitch header

Dimensions: 0.87 x 0.72" (22.22 x 18.48mm)

Documents:

Specifiche

Part. No. : SEN-11977

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Triple-Axis Digital-Output Gyro ITG-3200 Breakout

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Modulo Giroscopio - 3 assi - 250-2500°/sec - L3G4200D - I2C/SPI

    710612 Modulo Giroscopio - 3 assi - 250-2500°/sec - L3G4200D - I2C/SPI

    Modulo giroscopio a 3 assi basato sul sensore L3G4200D. Questo sensore ha una scala di ±250/±500/±2000 dps e può misurare confalse
    Prezzo di listino:
    € 48,79
    Offerta
    Tasse escluse:
    € 30,00
    IVA inclusa:
    € 36,60
      Confronta
  2. MOD-MPU6050 - MEMS 3-AXIS GYROSCOPE AND A 3-AXIS ACCELEROMETER

    502248 MOD-MPU6050 - MEMS 3-AXIS GYROSCOPE AND A 3-AXIS ACCELEROMETER

    MPU6050 is MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Pfalse
    Tasse escluse:
    € 9,90
    IVA inclusa:
    € 12,08
      Confronta
  3. L3GD20H Triple-Axis Gyro Breakout Board - L3GD20/L3G4200 Upgrade - L3GD20H

    808024 L3GD20H Triple-Axis Gyro Breakout Board - L3GD20/L3G4200 Upgrade - L3GD20H

    This breakout board is based around the latest gyro technology, the L3GD20H from STMicro. It's the upgrade to the L3G4200 witfalse
    Tasse escluse:
    € 11,79
    IVA inclusa:
    € 14,38
      Confronta