713746 SparkFun Beefy 3 - FTDI Basic Breakout

SparkFun Beefy 3 - FTDI Basic Breakout

This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
Categorie
Prezzi IVA inclusa
€ 16,47 Prezzo
€ 13,50 + VAT

Qty
 

Dettagli

This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more “Beefy” voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.

This board brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector. The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is DTR. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.

There are pros and cons to the FTDI Cable vs the FTDI Basic. This board has TX and RX LEDs that allow you to actually see serial traffic on the LEDs to verify if the board is working, however this board now requires a Micro-B USB cable. The FTDI Cable is well protected against the elements, but is large and cannot be embedded into a project as easily. The FTDI Basic uses DTR to cause a hardware reset where the FTDI cable uses the RTS signal.

This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro and LilyPad boards use this type of connector.

Documents:

Specifiche

Part. No. : DEV-13746

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on SparkFun Beefy 3 - FTDI Basic Breakout

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Adattatore USB->Seriale in miniatura

    990004 Adattatore USB->Seriale in miniatura

    L'adattatore seriale 990 004 e' ottimo per connettere microcontrollori e circuiti logici al PC. Il cuore del circuito e' il cfalse
    Prezzo di listino:
    € 11,83
    Offerta
    Tasse escluse:
    € 8,20
    IVA inclusa:
    € 10,00
      Confronta
  2. Cavo USB Mini-B 1,8mt

    711301 Cavo USB Mini-B 1,8mt

    Cavo USB 2.0 A to Mini-B 5-pin. Ottima qualita', firmato Sparkfun!
    Tasse escluse:
    € 3,68
    IVA inclusa:
    € 4,49
      Confronta
  3. FTDI Basic Breakout - 5V

    709716 FTDI Basic Breakout - 5V

    This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more cfalse
    Tasse escluse:
    € 12,17
    IVA inclusa:
    € 14,85
      Confronta
  4. FTDI Basic Breakout - 3.3V

    709873 FTDI Basic Breakout - 3.3V

    This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more cfalse
    Tasse escluse:
    € 14,49
    IVA inclusa:
    € 17,68
      Confronta
  5. SparkFun ESP8266 Thing - Dev Board

    713711 SparkFun ESP8266 Thing - Dev Board

    This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely design around the ESP8266, with an infalse
    Tasse escluse:
    € 12,84
    IVA inclusa:
    € 15,66
      Confronta