501381 VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record

VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record

Modulo lettore MP3, AAC, Ogg, etc... Basato sul chip VLSI VS1053B. Puo' leggere e registrare, tutte le regolazioni possono avvenire in digitale (bassi, alti, volume, etc.). Disponibili anche 8 GPIO per accendere LED o rilevare pulsanti. Slot SD card, interfaccia SPI.
Categorie
Prezzi IVA inclusa
€ 28,19 Prezzo
€ 23,11 + VAT

Qty
 

Dettagli

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and volume digitally. There is also 8 GPIO pins that can be used for stuff like lighting up small LEDs or reading buttons. 

All this functionality is implemented in a light-weight SPI interface so nearly any microcontroller can play audio from an SD card. There's also a special MIDI mode that you can boot the chip into that will read 'classic' 31250Kbaud MIDI data on a UART pin and act like a synth/drum machine - there are dozens of built-in drum and sample effects! But the chip is a pain to solder, and needs a lot of extras. That's why we spun up the best breakout, perfect for use with an Arduino but also good for other microcontrollers that just don't have the computational power to decode MP3s. 

The breakout is slim enough to fit on a breadboard with 1 row of holes left over for wiring. There's 3.3v and 1.8v regulators onboard with ferrite beads and analog filtering for quality analog output. There's a microphone input port that you can wire up a line-in or mic to and record compressed audio. All 8 GPIO are broken out and they all have built in 100K pulldowns, simply connect your button from the GPIO pin to 3.3V for an active-high connection. You'll likely want to play music from a microSD card so we added a holder on-board. And since we know so many of our customers use 5V microcontrollers like the Arduino, we made the interface pins all 5V compliant with level shifters so you can use the chip at 3V or 5V power/logic! 

Each order comes with a fully assembled and tested breakout board, two 100uF electrolytic capacitors for line-level output coupling, some 0.1" male header you can solder to the breakout so it plugs into a breadboard and a bonus stereo headphone jack that will be handy when you want to plug headphones in! 

New! As of Sept 24 2013, all orders will come with v2 which is nearly identical but now has 220uF stereo blocking capacitors on the output. This means you can plug the output into headphones or a stereo without risk of damage. Essentially we integrated the extra capacitors onto the PCB itself, saving you wiring and effort! If you have an older v1.0 which does not have the two big round silver capacitors on board, you can drive a pair of 30ohm headphones directly from the LOUT/ROUT pins if the 'ground' connection is tied to GBUF however this is not a line-out connection. If you want to connect to a stereo system or powered speakers with a v1.0 board, fit the two included 100uF electrolytic caps in series on the LOUT/ROUT pins between the breakout and the input of the stereo, then connect the common ground to AGND

Check out our detailed tutorial & excellent Arduino library that demonstrates everything cool about this library: playing music off an SD card, using the GPIO pins as input/outputs, playing music using an interrupt (so it's in the background), using the VS1053 as a MIDI synthesizer (no SD required), and recording Ogg vorbis audio from a microphone/line-in to SD.

Specifiche

Part. No. : 1381

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on VS1053 Codec + MicroSD Breakout - MP3/WAV/MIDI/OGG Play + Record

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Purpletooth Jamboree - BC127 Development Board

    711924 Purpletooth Jamboree - BC127 Development Board

    This is the PurpleTooth Jamboree a full-function board, designed to provide audio bridge support through the A2DP, HFP, and Afalse
    Tasse escluse:
    € 45,54
    IVA inclusa:
    € 55,56
      Confronta
  2. WAV Trigger

    713660 WAV Trigger

    The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities.
    Tasse escluse:
    € 38,48
    IVA inclusa:
    € 46,95
      Confronta
  3. SparkFun MP3 Player Shield

    712660 SparkFun MP3 Player Shield

    The SparkFun MP3 Player Shield is an awesome MP3 decoder with the capabilities of storing music files onto a run-of-the-mill false
    Tasse escluse:
    € 25,65
    IVA inclusa:
    € 31,29
      Confronta
  4. SparkFun RedStick

    713741 SparkFun RedStick

    The RedStick can be programmed by just plugging the board into your computer using the Arduino IDE: Just plug in the board, sfalse
    Tasse escluse:
    € 19,24
    IVA inclusa:
    € 23,47
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!