341367 1367 - High-Power Simple Motor Controller G2 24v19

1367 - High-Power Simple Motor Controller G2 24v19

Potente motor controller, controlla un motore DC, utilizzo molto semplice, 5 interfacce (usb, ttl, I2C, analogico, servo RC).
Categories
Prices are VAT included
€55.02 Price
€45.10 + VAT

 

Details

This powerful motor controller makes basic control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC). This version offers a wide 6.5 V to 40 V operating range and can deliver continuous output currents up to 19 A without a heat sink. Male headers and terminal blocks are included but not soldered, allowing for custom installations.

The Simple Motor Controllers are versatile, general-purpose single-channel motor controllers for brushed, DC motors. Wide operating voltage ranges and the ability to deliver up to several hundred watts in a small form factor make these controllers suitable for many motor control applications. With a variety of supported interfaces—­USB for direct connection to a computer, TTL serial and I²C for use with embedded systems, RC hobby servo pulses for use as an RC-controlled electronic speed control (ESC), and analog voltages for use with a potentiometer or analog joystick—­and a wide array of configurable settings, these motor controllers make it easy to add basic control of brushed DC motors to a variety of projects. A free configuration utility for Windows simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB.

The table below lists the all of the members of the Simple Motor Controller family and shows the key differences among them. Note that the information on this page is specific to the newer SMC G2s, which can generally be used as drop-in replacements for the original SMCs with green PCBs

Key features of the SMC G2 family

  • Simple bidirectional control of one brushed DC motor
  • Five communication or control options:
    1. USB interface for direct connection to a PC
    2. Logic-level (TTL) serial interface for use with a microcontroller
    3. I²C interface for use with a microcontroller
    4. Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller
    5. 0 V to 3.3 V analog voltage interface for direct connection to potentiometers and analog joysticks
  • Simple configuration and calibration over USB with a free configuration program for Windows
  • Reverse-voltage protection
  • Hardware current limiting with a configurable threshold
  • Current sensing

Additional features of the SMC G2 family

  • Adjustable maximum acceleration and deceleration to limit electrical and mechanical stress on the system
  • Adjustable starting speed and maximum speed
  • Option to brake or coast when speed is zero
  • Optional safety controls to avoid unexpectedly powering the motor
  • Input calibration (learning) and adjustable scaling degree for analog and RC signals
  • Under-voltage shutoff with hysteresis for use with batteries vulnerable to over-discharging (e.g. LiPo cells)
  • Adjustable over-temperature threshold and response
  • Adjustable PWM frequency from 1.13 kHz to 22.5 kHz (maximum frequency is ultrasonic, eliminating switching-induced audible motor shaft vibration)
  • Error LED linked to a digital ERR output, and connecting the error outputs of multiple controllers together optionally causes all connected controllers to shut down when any one of them experiences an error
  • Field-upgradeable firmware
  • Features of the serial, I²C, and USB interfaces:
    • Optional CRC error detection to eliminate communication errors caused by noise or software faults
    • Optional command timeout (shut off motors if communication ceases)
  • Serial features:
    • Controllable from a computer via serial commands sent to the device’s USB virtual serial (COM) port, or via TTL serial through the device’s RX/TX pins
    • TTL serial uses 0 V and 3.3 V on TX, accepts 0 V to 5 V on RX
    • Supports automatic baud rate detection from 1200 bps to 500 kbps, or can be configured to run at a fixed baud rate
    • Supports standard compact and Pololu protocols as well as the Scott Edwards Mini SSC protocol and an ASCII protocol for simple serial control from a terminal program
    • Optional serial response delay for communicating with half-duplex controllers such as the Basic Stamp
    • Controllers can be easily chained together and to other Pololu serial motor and servo controllers to control hundreds of motors using a single serial line
  • I²C features:
    • Compatible with I²C bus voltage levels from 1.8 V to 5 V
  • USB features:
    • Full-speed USB interface (12 Mbps)
    • Example code in C#, Visual Basic .NET, and Visual C++ is available in the Pololu USB Software Development Kit
  • RC features:
    • 1/4 µs pulse measurement resolution
    • Works with RC pulse frequencies from 10 to 333 Hz
    • Configurable parameters for determining what constitutes an acceptable RC signal
    • Two RC channels allow for single-stick (mixed) motor control, making it easy to use two simple motor controllers in tandem on an RC-controlled differential-drive robot
    • RC channels can be used in any mode as limit or kill switches (e.g. use an RC receiver to trigger a kill switch on your autonomous robot)
    • Battery elimination circuit (BEC) jumper can power the RC receiver with 5 V or 3.3 V
  • Analog features:
    • 0.8 mV (12-bit) measurement resolution
    • Works with 0 to 3.3 V inputs
    • Optional potentiometer/joystick disconnect detection
    • Two analog channels allow for single-stick (mixed) motor control, making it easy to use two simple motor controllers in tandem on a joystick-controlled differential-drive robot
    • Analog channels can be used in any mode as limit or kill switches

Dimensions

Size: 1.7″ × 1.2″ × 0.42″1
Weight: 9.7 g1

General specifications

Motor channels: 1
Control interface: USB; non-inverted TTL serial; I²C;
RC servo pulses; analog voltage2
Minimum operating voltage: 6.5 V
Maximum operating voltage: 40 V3
Continuous output current per channel: 19 A4
Maximum PWM frequency: 22.5 kHz
Maximum logic voltage: 3.3 V5
Reverse voltage protection?: Y
Version: G2 24v19 (40 V max, 19 A max continuous)
Connectors soldered?: N

Identifying markings

PCB dev codes: umc07a
Other PCB markings: 0J11559, blank white box

Notes:

1 Without included hardware.
2 Autodetects baud rates between 1200 and 500,000 bps, or can be set to any fixed baud rate in this range.
3 Absolute maximum; higher voltages can permanently destroy the motor driver. Recommended maximum is approximately 34 V, which leaves a safety margin for ripple voltage on the supply line.
4 Typical results at room temperature running at 90% duty cycle.
5 All digital inputs are 5V tolerant.

Product Page

Specifications

Part. No. : 1367

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on 1367 - High-Power Simple Motor Controller G2 24v19

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.
  1. 2994 - Pololu G2 High-Power Motor Driver 18v25

    342994 2994 - Pololu G2 High-Power Motor Driver 18v25

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ ×false
    Excl. Tax:
    €32.40
    Incl. Tax:
    €39.53
      Compare
  2. 3149 - Jrk G2 24v21 USB Motor Controller with Feedback

    343149 3149 - Jrk G2 24v21 USB Motor Controller with Feedback

    The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Excl. Tax:
    €142.00
    Incl. Tax:
    €173.24
      Compare
  3. 3148 - Jrk G2 18v27 USB Motor Controller with Feedback

    343148 3148 - Jrk G2 18v27 USB Motor Controller with Feedback

    The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Excl. Tax:
    €155.00
    Incl. Tax:
    €189.10
      Compare
  4. 3147 - Jrk G2 24v13 USB Motor Controller with Feedback

    343147 3147 - Jrk G2 24v13 USB Motor Controller with Feedback

    The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Excl. Tax:
    €110.00
    Incl. Tax:
    €134.20
      Compare
  5. 3146 - Jrk G2 18v19 USB Motor Controller with Feedback

    343146 3146 - Jrk G2 18v19 USB Motor Controller with Feedback

    The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Excl. Tax:
    €120.00
    Incl. Tax:
    €146.40
      Compare
  6. 1366 - High-Power Simple Motor Controller G2 18v25

    341366 1366 - High-Power Simple Motor Controller G2 18v25

    The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Excl. Tax:
    €45.10
    Incl. Tax:
    €55.02
      Compare
  7. 1365 - High-Power Simple Motor Controller G2 24v12

    341365 1365 - High-Power Simple Motor Controller G2 24v12

    The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Excl. Tax:
    €139.00
    Incl. Tax:
    €169.58
      Compare
  8. 2995 - Pololu G2 High-Power Motor Driver 24v21

    342995 2995 - Pololu G2 High-Power Motor Driver 24v21

    Ponte H a componenti discreti Mosfet, per il controllo bidirezionale di un motore DC ad alta potenza. Protezione, current senfalse
    Excl. Tax:
    €32.40
    Incl. Tax:
    €39.53
      Compare
  9. 1363 - High-Power Simple Motor Controller G2 18v15

    341363 1363 - High-Power Simple Motor Controller G2 18v15

    Potente motor controller, controlla un motore DC, utilizzo molto semplice, 5 interfacce (usb, ttl, I2C, analogico, servo RC).
    Excl. Tax:
    €100.00
    Incl. Tax:
    €122.00
      Compare