The compact (0.4″ × 0.5″) D24V3F5 switching step-down (or buck) voltage regulator takes an input voltage between 7 V and 42 V and efficiently reduces it to 5 V while allowing for a maximum output current of 300 mA. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
These buck (step-down) voltage regulators generate lower output voltages from input voltages as high as 42 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) and have a typical efficiency between 80% to 90%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large.
The regulator has short-circuit protection, and thermal shutdown prevents damage from overheating. The board does not have reverse-voltage protection.
- Input voltage: [output voltage + dropout voltage] to 42 V (see below for more information on dropout voltage)
- Fixed 3.3 V, 5 V, 9 V, or 12 V output (depending on regulator version) with 4% accuracy
- Maximum output current: 300 mA or 600 mA (depending on regulator version)
- 550 kHz switching frequency
- 2 mA typical no-load quiescent current (20 μA typical quiescent current with SHDN = LOW)
- Integrated over-temperature and over-current shutoff
- Small size: 0.5″ × 0.4″ × 0.1″ (13 mm × 10 mm × 3 mm)
Using the Regulator
The buck regulator has four connections: shutdown (SHDN), input voltage (VIN), ground (GND), and output voltage (VOUT).
The SHDN pin can be driven low (under 0.3 V) to turn off the output and put the board into a low-power state that typically draws 20 μA. TheSHDN pin can be driven high (above 2.3 V) to enable the board, or it can be connected to VIN or left disconnected if you want to leave the board permanently enabled.
The input voltage, VIN, should exceed VOUT by at least the regulator’s dropout voltage (see below for graphs of dropout voltages as a function of the load), and you must ensure that noise on your input does not exceed the 42 V maximum. Additionally, please be wary of destructive LC spikes (see below for more information).
The output voltage, VOUT, is fixed and depends on the regulator version: the D24VxF3 version outputs 3.3 V, the D24VxF5 version outputs 5 V, the D24VxF9 version outputs 9 V, and the D24VxF12 version outputs 12 V.
The four connections are labeled on the back side of the PCB, and they are arranged with a 0.1″ spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. You can solder wires directly to the board or solder in either the 4×1 straight male header strip or the 4×1 right-angle male header strip that is included.
Typical Efficiency and Output Current
The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graphs below, this switching regulator typically has an efficiency of 80% to 90%.
Typical Dropout Voltage
The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V.
LC Voltage Spikes
When connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage (42 V), the regulator can be destroyed. In our tests with typical power leads (~30″ test clips), input voltages above 20 V caused spikes over 42 V. If you are connecting more than 20 V or your power leads or supply has high inductance, we recommend soldering a 33μF or larger electrolytic capacitor close to the regulator between VIN and GND. The capacitor should be rated for at least 50 V.
|Size:||0.4″ × 0.5″ × 0.1″1|
|Minimum operating voltage:||6 V2|
|Maximum operating voltage:||42 V|
|Maximum output current:||300 mA|
|Output voltage:||5 V|
|Reverse voltage protection?:||N|
|Maximum quiescent current:||2 mA3|
- Without included optional headers.
- For small loads; input voltage must be at least 6.5 V to get the full 300 output.
- While enabled (SHDN = HIGH) with no load. Current draw is approximately 20 µA when SHDN = LOW.
|Part. No. :||2098|
Questions on 2098 - Pololu 5V, 300mA Step-Down Voltage Regulator D24V3F5
No questions asked yetRegister or Login to ask a question.
220003 L7805 Voltage Regulator Excl. Tax:€0.42Incl. Tax:€0.51
582560 2560 - Pololu Adjustable Step-Up Voltage Regulator U1V11AThis compact U1V11A switching step-up (or boost) voltage regulator efficiently boosts input voltages as low as 0.5 V to an adfalseExcl. Tax:€4.67Incl. Tax:€5.70
342850 2850 - Pololu 5V, 2.5A Step-Down Voltage Regulator D24V25F5This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces ifalseExcl. Tax:€25.00Incl. Tax:€30.50
342851 2851 - Pololu 5V, 5A Step-Down Voltage Regulator D24V50F5This step-down (buck) regulator generates a fixed 5 V output from input voltages up to 38 V. It is a switching regulator (alsfalseExcl. Tax:€12.28Incl. Tax:€14.98
342577 2577 - Pololu 12V Step-Up/Step-Down Voltage Regulator S18V20F12This powerful step-up/step-down regulator efficiently produces a fixed 12 V output from input voltages between 3 V and 30 V wfalseExcl. Tax:€26.00Incl. Tax:€31.72
342834 2834 - Pololu 12V, 1A Step-Down Voltage Regulator D24V10F12The compact D24V10F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 1falseExcl. Tax:€6.68Incl. Tax:€8.15
342831 2831 - Pololu 5V, 1A Step-Down Voltage Regulator D24V10F5The compact D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5falseExcl. Tax:€6.68Incl. Tax:€8.15
342830 2830 - Pololu 3.3V, 1A Step-Down Voltage Regulator D24V10F3The compact D24V10F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.falseExcl. Tax:€6.27Incl. Tax:€7.65
342843 2843 - Pololu 5V, 500mA Step-Down Voltage Regulator D24V5F5The compact D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 VfalseExcl. Tax:€7.00Incl. Tax:€8.54
342587 2587 - Breakout Board for microSD Card with 3.3V Regulator and Level ShiftersThis compact board breaks out the pins of a microSD card connector necessary to interface with the card through SPI (Serial PfalseExcl. Tax:€10.00Incl. Tax:€12.20
342855 2855 - Pololu 12V, 2.2A Step-Down Voltage Regulator D24V22F12This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces ifalseExcl. Tax:€8.79Incl. Tax:€10.72
342857 2857 - Pololu 3.3V, 2.6A Step-Down Voltage Regulator D24V22F3This small synchronous switching step-down (or buck) regulator takes an input voltage from 4 V to 36 V and efficiently reducefalseExcl. Tax:€27.80Incl. Tax:€33.92