344756 4756 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder (Helical Pinion)

4756 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder (Helical Pinion)

Motoriduttore 12V con encoder a quadratura ad alta risoluzione. Con ingranaggi helical, riducono il rumore ed aumentano l'efficienza
Categories
Prices are VAT included
€38.43 Price
€31.50 + VAT

Qty
 

Details

This gearmotor is a powerful 12V brushed DC motor with a 131.25:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 8400 counts per revolution of the gearbox’s output shaft. The gearbox is composed mainly of spur gears, but it features helical gears for the first stage for reduced noise and improved efficiency. These units have a 16 mm-long, 6 mm-diameter D-shaped output shaft. 

Key specifications:

voltageno-load performancestall extrapolation
12 V 76 RPM, 150 mA 45 kg⋅cm (630 oz⋅in), 5.5 A

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. In order to avoid damaging the gearbox, we recommend keeping continuously applied loads under 10 kg-cm (150 oz-in), and the recommended upper limit for instantaneous torque is 25 kg-cm (350 oz-in). Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

These motors are intended for use at 12 V, though in general, these kinds of motors can run at voltages above and below the nominal voltage (they can begin rotating at voltages as low as 1 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 8″ (20 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. 

Dimensions

Size: 37D × 72.5L mm1
Weight: 210 g
Shaft diameter: 6 mm2

General specifications

Gear ratio: 131.25:1
No-load speed @ 12V: 76 rpm
No-load current @ 12V: 0.15 A
Stall current @ 12V: 5.5 A3
Stall torque @ 12V: 45 kg·cm3
Max output power @ 12V: 6 W
No-load speed @ 6V: 38 rpm4
No-load current @ 6V: 0.1 A4
Stall current @ 6V: 3.0 A5
Stall torque @ 6V: 28 kg·cm5

Performance at maximum efficiency

Max efficiency @ 12V: 45 %
Speed at max efficiency: 66 rpm
Torque at max efficiency: 6.0 kg·cm
Current at max efficiency: 0.74 A
Output power at max efficiency: 4.1 W

General specifications

Lead length: 20 cm6
Encoders?: Y
Encoder resolution: 64 CPR

Notes:

1 Length measurement is from gearbox face plate to back of encoder cap (it does not include the output shaft). See dimension diagram for details.
2 D shaft.
3  Stalling is likely to damage the gearmotor. Stall parameters come from a theoretical extrapolation of performance at loads far from stall. As the motor heats up, as happens as it approaches an actual stall, the stall torque and current decrease.
4 This motor will run at 6 V but is intended for operation at 12 V.
5 Stalling is likely to damage the gearmotor. Stall parameters come from a theoretical extrapolation of performance at loads far from stall. This motor will run at 6 V but is intended for operation at 12 V.
6 May vary by a few centimeters.

Product Page

Specifications

Part. No. : 4756
Shaft Diam. mm : 6

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on 4756 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder (Helical Pinion)

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.
  1. Gearmotor 12Vdc 81RPM Encoder

    420114 Gearmotor 12Vdc 81RPM Encoder

    Gearbox : Voltage 12 Vdc Torque 5.1 Kg/cm 81 RPM Shaft diameter 6 mm Encoder 3 pulses / revolution
    Excl. Tax:
    €17.91
    Incl. Tax:
    €21.85
      Compare
  2. Gearmotor 12Vdc 66RPM Encoder

    420115 Gearmotor 12Vdc 66RPM Encoder

    Gearbox : Voltage 12 Vdc Torque 6.12 Kg/cm 66 RPM Shaft diameter 6 mm Encoder 3 pulses / revolution
    Excl. Tax:
    €17.91
    Incl. Tax:
    €21.85
      Compare
  3. Gearmotor 12Vdc 33RPM Encoder

    420116 Gearmotor 12Vdc 33RPM Encoder

    Gearbox : Voltage 12 Vdc Torque 10.2 Kg/cm 33 RPM Shaft diameter 6 mm Encoder 3 pulses / revolution
    Excl. Tax:
    €17.91
    Incl. Tax:
    €21.85
      Compare
  4. 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors

    582566 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors

    These aluminum gearmotor brackets let you mount Pololu’s 37D mm metal gearmotors to your project. The brackets are sold in pafalse
    Excl. Tax:
    €5.88
    Incl. Tax:
    €7.17
      Compare
  5. 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

    342826 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

    This gearmotor is a powerful 12V brushed DC motor with a 102.083:1 metal gearbox and an integrated quadrature encoder that prfalse
    Excl. Tax:
    €31.40
    Incl. Tax:
    €38.31
      Compare
  6. 2825 - 70:1 Metal Gearmotor 37Dx70L mm with 64 CPR Encoder

    342825 2825 - 70:1 Metal Gearmotor 37Dx70L mm with 64 CPR Encoder

    This gearmotor is a powerful 12V brushed DC motor with a 70:1 metal gearbox and an integrated quadrature encoder that providefalse
    Excl. Tax:
    €29.23
    Incl. Tax:
    €35.66
      Compare

Price Match



* Required Fields