120125 DFRduino Ethernet Shield V2.1 (Support Mega and Micro SD)

DFRduino Ethernet Shield V2.1 (Support Mega and Micro SD)

The DFRduino Ethernet Shield V2.1 is now released. This version of Ethernet Shield is not only compatible with Mega 1280 and 2560, but also provides a Micro SD card slot for reading/writing.
Categories
Prices are VAT included
€16.59 Price
€13.60 + VAT

Qty
 

Details

The DFRduino Ethernet Shield V2.1 is now released. This version of Ethernet Shield is not only compatible with Mega 1280 and 2560, but also provides a Micro SD card slot for reading/writing.  

DFRduino Ethernet Shield V2.1 is fully compatible with Ardunio Ethernet Shield. With the offical ethernet library, you can do exactly the same thing as the original one, but at a more affordable price. 

This Ethernet Shield provides an Arduino controller board with internet access. It is based on the Wiznet W5100 ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. You can use the Ethernet library to write sketches which connect to the internet using the shield.

You can connect the Ethernet Shield to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

Arduino uses digital pins 10, 11, 12, and 13 (SPI) to communicate with the W5100 on the ethernet shield. These pins cannot be used for general i/o.

The shield provides a standard RJ45 ethernet jack.

The reset button on the shield resets both the W5100 and the Arduino board.

The shield contains a number of informational LEDs:

  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected 
 

Compatibility

  • Arduino Mega 1280/2560
  • Arduino UNO
  • Arduino Dumlinove

 

 

 

DOCUMENTS

 

 

 

 

 

SHIPPING LIST

 

 

  • DFRduino Ethernet Shield x1

Specifications

Part. No. : DFR0125
Interface : SPI
Voltage : 5
Shield Type : Communication, Ethernet

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on DFRduino Ethernet Shield V2.1 (Support Mega and Micro SD)

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.
  1. ProtoScrewShield v1.5

    709729 ProtoScrewShield v1.5

    The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals.
    Excl. Tax:
    €12.03
    Incl. Tax:
    €14.68
      Compare
  2. Screw Shield

    115073 Screw Shield

    Screw shield is a wing-like shield that extends both sides of your Arduino or Arduino variants into sturdy and reliable screwfalse
    Excl. Tax:
    €8.20
    Incl. Tax:
    €10.00
      Compare
  3. Proto-Screwshield (Wingshield) R3 Kit for Arduino

    807888 Proto-Screwshield (Wingshield) R3 Kit for Arduino

    The next generation Proto-ScrewShield is a dual-purpose prototyping shield. Now only does it have a large 0.1" grid protfalse
    Excl. Tax:
    €15.42
    Incl. Tax:
    €18.81
    As low as:
    €13.42
      Compare

Price Match



* Required Fields