The DMX-USB-RX-A8 module is a fully compliant with the latest USITT DMX512-A standard, E1.11-2004. This small module, powered by a single 18VAC supply, provides 8 analogue outputs.
Fully compliant with the latest USITT DMX512-A standard.
Backwards compatible with the older USITT DMX512/1990 standard.
Easy to use configuration via a USB port. PC application supplied, no dip switches to worry about.
Uses a single 18VAC supply for power.
Module can be set to any DMX address from 1-504 .
Output ranges may be individually set from 0 to +/- 5v, up to 0 to +/-15v
DMX feed though on all pins, including 4 & 5.
Selectable 120 Ohm termination.
Power can be connected to the module either from an 18v AC transformer to the two pin screw terminals, or from an 18v AC adapter. The module cannot be powered from the USB port. The 120 ohm terminating link connects an on-board 120 ohm resistor across the DMX. This should only be fitted to the last module on the DMX cable. Remove the link on ALL other modules.
The default factory settings for your DMX-USB-RX-A8 module is DMX address 1 and 0 to +10v outputs. If this is what you need, then just connect the 18VAC supply, plug in the DMX cable and your away.
It's more likely that you want to select a different DMX address and to change the output voltages. To do this you will need a PC running Windows XP/Vista/Win7.
You will need:
The DMX_A8 Configuration program.
The USB driver for windows.
Unzip the DMX_A8 Installation file into a temporary folder and click "setup" to install it.
Next install the USB driver. If your using Vista, temporarily disconnect your internet connection by unplugging the network cable or switching off the wireless connection. This is because Vista will go off and look for a suitable driver and not offer you the chance to direct it to the correct driver. It will probably install the wrong driver. Disconnecting the internet first will force it to ask you where to look. XP is fine, it asks you anyway. Connect the 18vac supply to the module, then plug in the USB cable. Windows should detect the new module and ask for the driver. Direct windows to the "inf" folder and windows will install the driver. Once installed you will have a new serial comm. port listed in Device Manager.
Run the DMX_A8 Configuration program, and you will see the following dialog. Select the new comm. port and it will find the module and display its software revision number. The DMX address the module is currently set to is displayed and the calibration values.
Changing the Output voltages
Important - Disconnect the DMX cables before you do this. Incoming DMX will corrupt the calibration.
To change the output voltage from the factory default 0 to 10v range, you will need volt meter (multi-meter). Connect this to the 1st channel you wish to modify. The first thing to do is to set the zero voltage level. Click the "Zero" button. Note that all the DMX levels have changed. They are no-longer the DMX levels, but internal calibration values. Note also the "Clear" and "Store" buttons and Sliders have become active. Using the sliders adjust the level on the multi-meter to read as close to 0v as possible. You should be able to get within 8mV of 0v. The zero volt calibration is only done once and affects all channels. It can be done on any channel.
Now the maximum output can be set. Select the channel you which to calibrate, and adjust the coarse and fine sliders. You should be able to get within 8mV of your target. Repeat this for each of the outputs. When you have finished, check and change the DMX address if required, then click "Store", this will save the new calibration data in the non-volatile memory on the DMX-USB-RX-A8 module. Disconnect the USB cable and re-connect the DMX cable.
When you press "Store" (or "Clear" to discard changes), The dialog will revert to displaying DMX levels:
Changing the DMX address
The DMX address can be set to any between 1 and 505. Just enter the new address in the "DMX Addr" edit box and click the "Update Address" button. The 8 channels on the DMX-USB-RX-A8 module are numbered consecutively. If you select address 505, then channel A1 will be at address 505, channel A2 will be at address 506 and channel A8 will be at address 512.
The 5-pin XLR connections follow industry standard pin-out.
|Use||5-pin XLR Pin number||DMX512 Function|
|Common Reference||1||Data Link Common|
|Primary Data Link||2||Data 1-|
|Secondary Data Link
(unused by module, but connected through on XLR's)
If the module is the last one on the DMX cable, you should ensure the link is fitted on the board. This will enable the 120 ohm terminating resistor.
Where the DMX is feeding through to other modules further down the cable, this link should be removed.
Questions on DMX-USB-RX-A8 DMX512, 8-channel Analogue Output Module
No questions asked yetRegister or Login to ask a question.
312002 DMX-USB-RX-D8 DMX512, 8-channel Digital Output ModuleFully compliant with the latest USITT DMX512-A standard. Backwards compatible with the older USITT DMX512/1990 standard. EafalseExcl. Tax:€52.50Incl. Tax:€64.05
312010 DMX-USB-RX-RLY8 Relay Output Module 0 Relay 8 DimmersFully compliant with the latest USITT DMX512-A standard. Backwards compatible with the older USITT DMX512/1990 standard. EafalseExcl. Tax:€104.11Incl. Tax:€127.01
809499 USB-RS485B - Low cost DMX512 TransmitterInterfaccia USB to RS485 funzionante a qualsiasi baud rate fino a 250k baud. Fino a 128 dispositivi sul bus. Puo' essere usatfalseExcl. Tax:€19.83Incl. Tax:€24.19