342827 2827 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

2827 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

This gearmotor is a powerful 12V brushed DC motor with a 131.25:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 8400 counts per revolution of the gearbox’s output shaft.
Categories
Prices are VAT included
€42.14 Price
€34.54 + VAT

Qty
 

Details

This gearmotor is a powerful 12V brushed DC motor with a 131.25:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 8400 counts per revolution of the gearbox’s output shaft. These units have a 0.61"-long, 6 mm-diameter D-shaped output shaft.
 

Key specs at 12 V: 80 RPM and 300 mA free-run, 250 oz-in (18 kg-cm) and 5 A stall.

These motors are intended for use at 12 V, though in general, these kinds of motors can run at voltages above and below the nominal voltage (they can begin rotating at voltages as low as 1 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 11" (28 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions:

ColorFunction
Red motor power (connects to one motor terminal)
Black motor power (connects to the other motor terminal)
Green encoder GND
Blue encoder Vcc (3.5 – 20 V)
Yellow encoder A output
White encoder B output

The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. 

Dimensions

Size: 37D x 72.5L mm1
Weight: 235 g
Shaft diameter: 6 mm

General specifications

Gear ratio: 131:1
Free-run speed @ 6V: 40 rpm2
Free-run current @ 6V: 250 mA2
Stall current @ 6V: 2500 mA2
Stall torque @ 6V: 125 oz·in2
Free-run speed @ 12V: 80 rpm
Free-run current @ 12V: 300 mA
Stall current @ 12V: 5000 mA
Stall torque @ 12V: 250 oz·in
Lead length: 11 in

Notes:

1 Length measurement does not include gearbox shaft or the raised area immediately around it.
2 This motor will run at 6 V but is intended for operation at 12 V.

Specifications

Part. No. : 2827
Shaft Diam. mm : 6

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on 2827 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.
  1. Gearmotor 12Vdc 81RPM Encoder

    420114 Gearmotor 12Vdc 81RPM Encoder

    Gearbox : Voltage 12 Vdc Torque 5.1 Kg/cm 81 RPM Shaft diameter 6 mm Encoder 3 pulses / revolution
    Excl. Tax:
    €17.91
    Incl. Tax:
    €21.85
      Compare
  2. Gearmotor 12Vdc 66RPM Encoder

    420115 Gearmotor 12Vdc 66RPM Encoder

    Gearbox : Voltage 12 Vdc Torque 6.12 Kg/cm 66 RPM Shaft diameter 6 mm Encoder 3 pulses / revolution
    Excl. Tax:
    €17.91
    Incl. Tax:
    €21.85
      Compare
  3. Gearmotor 12Vdc 33RPM Encoder

    420116 Gearmotor 12Vdc 33RPM Encoder

    Gearbox : Voltage 12 Vdc Torque 10.2 Kg/cm 33 RPM Shaft diameter 6 mm Encoder 3 pulses / revolution
    Excl. Tax:
    €17.91
    Incl. Tax:
    €21.85
      Compare
  4. 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors

    582566 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors

    These aluminum gearmotor brackets let you mount Pololu’s 37D mm metal gearmotors to your project. The brackets are sold in pafalse
    Excl. Tax:
    €6.50
    Incl. Tax:
    €7.93
      Compare
  5. 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

    342826 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder

    This gearmotor is a powerful 12V brushed DC motor with a 102.083:1 metal gearbox and an integrated quadrature encoder that prfalse
    Excl. Tax:
    €32.40
    Incl. Tax:
    €39.53
      Compare
  6. 2828 - 150:1 Metal Gearmotor 37Dx73L mm 12V with 64 CPR Encoder (Helical Pinion)

    342828 2828 - 150:1 Metal Gearmotor 37Dx73L mm 12V with 64 CPR Encoder (Helical Pinion)

    This gearmotor is a powerful 12V brushed DC motor with a 150:1 metal gearbox and an integrated quadrature encoder that providfalse
    Excl. Tax:
    €38.00
    Incl. Tax:
    €46.36
      Compare