The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 100lbs in combat or 300lbs for general purpose robotics. Out of the box, the Sabertooth can supply two DC brushed motors with up to 25A each. Peak currents of 50A per channel are achievable for a few seconds. Overcurrent and thermal protection means you'll never have to worry about killing the driver with accidental stalls or by hooking up too big a motor.
Sabertooth allows you to control two motors with: analog voltage, radio control, serial and packetized serial. You can build many different robots of increasing complexity for years to come with a Sabertooth. Sabertooth has independent and speed+direction operating modes, making it the ideal driver for differential drive (tank style) robots and more. The operating mode is set with the onboard DIP switches so there are no jumpers to lose. Sabertooth features screw terminal connectors - making it possible for you to build a robot without even soldering. Sabertooth is the first synchronous regenerative motor driver in its class. The regenerative topology means that your batteries get recharged whenever you command your robot to slow down or reverse. Sabertooth also allows you to make very fast stops and reverses - giving your robot a quick and nimble edge.
Sabertooth has a built in 5V BEC that can provide power to a microcontroller or R/C receiver. The lithium cutoff mode allows Sabertooth to operate safely with lithium ion and lithium polymer battery packs - the highest energy density batteries available. Sabertooth's transistors are switched at ultrasonic speeds (32kHz) for silent operation. Sabertooth 2X25 uses 1.3 milliohm MOSFETs in its bridge. Going by our competitor's ridiculous rating schemes this would make it a dual 190A motor driver! Use of our motor drivers with cheap AC adapters is not recommended. Use a battery or at least put a battery in parallel with a DC supply.
|Specifications:||25A continuous, 50A peak per channel.
6-24V nominal, 30V absolute maximum
Synchronous regenerative drive
Ultra-sonic switching frequency
Thermal and overcurrent protection
Lithium protection mode
Input modes: Analog, R/C, simplified serial, packetized serial
Size: 2.6” x 3.2” x .8”
65 x 80 x 20 mm
|Documentation:||Sabertooth 2x25V2.doc (2.6mb)
Sabertooth 2x25.doc (2.6mb)
Sabertooth 2x25.pdf (1.9mb)
Quick start guide.doc
Quick start guide.pdf
Sabertooth DIP Switch Wizard
Motor driver efficiency comparison Sample RPM versus throttle graph
|Applications:||Combat robots up to 100lb
Normal and hobby robots up to 300lb
Differential drive robots
Electric vehicles, ride-on toys, scooters
Easy speed/direction control for pumps, conveyors, automation and any application that uses two brushed DC motors
|Application notes:||Using a SyRen/Sabertooth with an ATX (or similar) DC power supply
Packetized mode with a PIC and Sabertooth
Questions on Sabertooth dual 2x25A V2 motor driver
No questions asked yetRegister or Login to ask a question.
330018 Sabertooth 2X5 Motor Controller 2X5ASabertooth 2X5 is the motor driver of choice for small differential-drive robots.Excl. Tax:€47.90Incl. Tax:€58.44
330019 Sabertooth 2X12 Motor Controller 2X12AThe Sabertooth 2X12 is one of the most versatile, efficient and easy to use dual motor drivers on the market.Excl. Tax:€62.30Incl. Tax:€76.01
330026 Sabertooth dual 32A motor driverSabertooth 2x32 is a dual channel motor driver capable of supplying 32 amps to two motors, with peak currents up to 64 amps pfalseExcl. Tax:€101.80Incl. Tax:€124.20
330027 Kangaroo x2 motion controllerKangaroo x2 adds self-tuning feedback motion control to your Sabertooth or SyRen motor driver. It can be used with quadraturefalseExcl. Tax:€19.80Incl. Tax:€24.16
808714 Sabertooth dual 60A motor driverSabertooth 2x60 can supply two DC brushed motors with up to 60A each. Peak currents of 120A per channel are achievable for a falseExcl. Tax:€149.60Incl. Tax:€182.51