341112 1112 - Pololu Qik 2s12v10 Dual Serial Motor Controller

1112 - Pololu Qik 2s12v10 Dual Serial Motor Controller

Controller motori seriale con autobaud. Permette il controllo simultaneo di due motori funzionanti ad una tensione tra 6 e 16V e con un assorbimento massimo di 13A continui per motore. Frequenza PWM e baudrate configurabili.
Categorie
Prezzi IVA inclusa
€ 103,70 Prezzo
€ 85,00 + VAT

Qty
 

Dettagli

 

This powerful motor controller allows variable speed and direction control of two large, brushed DC motors using a simple serial interface and provides several advanced features, such as motor acceleration control and configurable current limiting. Automatic baud detection up to 115.2 kbps and inputs for both RS-232 and TTL serial make it easy to add motors to your microcontroller- or computer-based project. The operating voltage range is 6 to 16 V; the continuous current per channel is up to 13 A (30 A peak).

The qik 2s12v10 adds a comprehensive yet easy-to-use, high-power option to Pololu’s line of motor controllers. The compact board allows any microcontroller or computer with a serial port to drive two brushed DC motors with full direction and speed control, providing up to 13 A (continuous) per motor channel without a heat sink and tolerating peaks as high as 30 A.

The improvements over competing products include:

  • high-frequency PWM to eliminate switching-induced motor shaft hum or whine
  • a robust, high-speed communication protocol with user-configurable error condition response
  • visible LEDs and a demo mode to help troubleshoot problematic installations
  • reverse power protection

For a lower-power version of this controller, please consider the qik 2s9v1 (see related products). For similar devices that support additional features and control interfaces, please consider the Simple High-Power Motor Controllers, TReX motor controller, and jrk 12v12 motor controller with feedback. For a robot controller based on the qik’s drivers, please consider the Orangutan X2 robot controller, which connects the VNH2SP30s to a user-programmable ATmega1284 AVR microcontroller.

Main Features of the Qik 2s12v10

  • Simple bidirectional control of two DC brush motors.
  • 6 V to 16 V operating supply range.
  • 13 A maximum continuous current per motor (30 A peak).
  • Logic-level, non-inverted, two-way serial control for easy connection to microcontrollers or robot controllers.
  • RS-232-level, one-way serial control for easy connection to a PC serial port.
  • Optional automatic baud rate detection from 1200 bps to 115.2 kbps.
  • Seven on-board indicator LEDs (power, status/heartbeat, error indicator, and motor indicators) for debugging and feedback.
  • Advanced features include configurable acceleration, motor current feedback, and current limiting.
  • Error output to make it easier for the main controller to recover from an error condition.
  • Optional motor shutdown on error or serial timeout for additional safety.
  • Jumper-enabled demo mode allows initial testing without any programming.
  • Optional CRC error detection eliminates serial errors caused by noise or software faults.
  • Comprehensive user’s guide.

Specifications

  • Motor channels: 2
  • Operating voltage: 6 – 16 V
  • Continuous output current per channel: 13 A
  • Peak output current per channel: 30 A
  • Auto-detect baud rate range: 1200 – 115,200 bps
  • Available fixed baud rates: 115,200 bps, 38,400 bps, 9600 bps
  • Available PWM frequencies: 19.7 kHz, 9.8 kHz, 2.5 kHz, 1.2 kHz, 310 Hz, 150 Hz
  • Reverse voltage protection
  • Motor driver: VNH2SP30 x2

Included Hardware

The qik ships with a 12×1 straight 0.100" male header strip, a 3×2 straight 0.100" male header strip, three 2-pin terminal blocks, and three red shorting blocks.

For the most compact installation, you can solder wires directly to the qik pins themselves and skip using the included hardware. For high-current installations, you should avoid using the supplied terminal blocks, which are rated for up to 15 A, and instead directly solder the motor and power supply wires to the pads.

The included hardware allows you to make less permanent connections. You can break the 12×1 header strip into a 6×1 piece and two 2×1 pieces and solder these strips into the qik’s logic pins where you plan on making connections, or you can use a pair of pliers to pull out the two header pins in the original 12×1 strip for which the qik has no holes and solder the entire strip to the qik’s logic pins. You can see this latter approach in the picture above. You can then make your own cables that have female headers on them and plug these onto the male headers on your qik, or you can solder the pins to the other side of the board and simply plug your qik into a breadboard. You might also consider using a 0.100" right-angle male header strip (not included) for a lower profile.

The 3×2 header strip can be soldered to the jumper pins, which lets you make use of the included shorting blocks, and the included terminal blocks lock together to make a single, 6-pin strip that you can solder to the power side of the board.

Documents 

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 1112 - Pololu Qik 2s12v10 Dual Serial Motor Controller

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).