Dettagli
This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an operating voltage range from 2.7 to 10.8 V and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature, this driver is a great solution for powering small, low-voltage motors.
Texas Instruments’ DRV8833 is a dual H-bridge motor driver IC that can be used for bidirectional control of two brushed DC motors at 2.7 to 10.8 V. It can supply up to about 1.2 A per channel continuously and can tolerate peak currents up to 2 A per channel for a few seconds, making it an ideal driver for small motors that run on relatively low voltages. Since this board is a carrier for the DRV8833, we recommend careful reading of the DRV8833 datasheet (1MB pdf). The board ships populated with SMD components, including the DRV8833, and adds a FET for reverse battery protection.
This board is very similar to our DRV8835 dual motor driver carrier in operating voltage range and continuous current rating, but the DRV8835 has a lower minimum operating voltage, offers an extra control interface mode, and is 0.1″ smaller in each dimension. The DRV8833 has a higher peak current rating (2 A per channel vs 1.5 A), optional built-in current-limiting, and no need for externally supplied logic voltage.
Features
- Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
- Operating voltage: 2.7–10.8 V
- Output current: 1.2 A continuous (2 A peak) per motor
- Motor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor
- Inputs are 3V- and 5V-compatible
- Under-voltage lockout and protection against over-current and over-temperature
- Reverse-voltage protection circuit
- Current limiting can be enabled by adding sense resistors (not included)
In a typical application, power connections are made on one side of the board and control connections are made on the other. The nSLEEP pin is pulled high on the board and can be left disconnected if you do not want to use the low-power sleep mode of the DRV8833. Each of the two motor channels has a pair of control inputs, xIN1 and xIN2, that set the state of the corresponding outputs, xOUT1 and xOUT2; pulse width modulated (PWM) signal can be applied to each of these inputs. The control inputs are pulled low internally, effectively disabling the motor driver outputs by default. See the truth tables in the DRV8833 datasheet for more information on how the inputs affect the driver outputs.
The nFAULT pin is an open-drain output that is driven low by the chip whenever an over-current, over-temperature-or under-voltage condition occurs. Otherwise, it remains in a floating state, so you will need to connect an external pull-up resistor (or use a microcontroller input with its built-in pull-up enabled) if you want to monitor fault conditions on the driver.
Dimensions
Size: |
0.5″ × 0.8″1 |
Weight: |
1.0 g1 |
General specifications
Motor driver: |
DRV8833 |
Motor channels: |
2 |
Minimum operating voltage: |
2.7 V |
Maximum operating voltage: |
10.8 V |
Continuous output current per channel: |
1.2 A2 |
Peak output current per channel: |
2 A |
Continuous paralleled output current: |
2.4 A2 |
Reverse voltage protection?: |
Y |
Notes:
1 Without included hardware.
2 Typical results with 100% duty cycle at room temperature.
Specifiche
Part. No. : | 2130 |
Questions on 2130 - DRV8833 Dual Motor Driver Carrier
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
709457 Motor Driver 1A Dual TB6612FNG
Modulo per controllare due motori DC fino a 1.2A. -
711890 MiniMoto - DRV8830 Breakout
Motor Controller basato sul Chip DRV8830, controlla un Motore a spazzole, con tensione da 2,7V a 6,8V e 1A di potenza max. Sifalse -
807832 2135 - DRV8835 Dual Motor Driver Carrier
This tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pairfalse -
807833 713 - TB6612FNG Dual Motor Driver Carrier
This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectionafalse -
807834 2137 - A4990 Dual Motor Driver Carrier
This compact breakout board makes it easy to use Allegro’s A4990 dual motor driver, which can control two bidirectional DC mofalse -
342990 2990 - DRV8838 Single Brushed DC Motor Driver Carrier
This tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. -
342753 2753 - Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+ and provides an easy and low-cost solutfalse -
808734 Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max
This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. In particular, the simple false -
808845 Adafruit DRV8833 DC/Stepper Motor Driver Breakout Board
Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driverfalse