582133 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

2133 - DRV8825 Stepper Motor Driver Carrier, High Current

Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 1.5A per fase, fino a 2.2A con dissipatore (non fornito). Gestione microstep.
Prezzi IVA inclusa
€ 9,06 Prezzo
€ 7,43 + VAT

 

Dettagli

The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).

Overview

This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerationssection below for more information). Here are some of the driver’s key features:

  • Simple step and direction control interface
  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Intelligent chopping control that automatically selects the correct current decay mode (mixed decay or slow decay)
  • 45 V maximum supply voltage
  • Built-in regulator (no external logic voltage supply needed)
  • Can interface directly with 3.3 V and 5 V systems
  • Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
  • Short-to-ground and shorted-load protection
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB
  • Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)

We also carry a DRV8824 stepper motor driver carrier that can serve as a direct substitute for the DRV8825 carrier when using lower-current stepper motors. The DRV8824 can only deliver up to 0.75 A per coil without a heat sink (1.2 A max with proper cooling), but it has larger current-sense resistors that allow for better microstepping performance than the DRV8825 carrier at low currents. The only way to tell our DRV8824 carrier apart from the DRV8825 carrier is by the markings on the driver IC; if you have a mix of the two, you might consider marking them (there is a blank square on the bottom silkscreen you can use for this).

This product ships with all surface-mount components—including the DRV8825 driver IC—installed as shown in the product picture.

Some unipolar stepper motors (e.g. those with six or eight leads) can be controlled by this driver as bipolar stepper motors. Unipolar motors with five leads cannot be used with this driver.

Included hardware

The DRV8825 stepper motor driver carrier ships with one 1×16-pin breakaway 0.1" male header. The headers can be soldered in for use with solderless breadboards or 0.1" female connectors. You can also solder your motor leads and other connections directly to the board.

Texas Instruments DRV8825 stepper motor driver datasheet (1MB pdf)

DRV8824/DRV8825 stepper motor driver carrier schematic diagram (196k pdf)

Specifiche

Part. No. : 2133

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. BB-A4983 - TWO CHANNEL STEPPER MOTOR DRIVER

    502260 BB-A4983 - TWO CHANNEL STEPPER MOTOR DRIVER

    A4983 driver can control stepper motors and have two channels. The board can also power gear motors. It might be supplied by false
    Tasse escluse:
    € 9,00
    IVA inclusa:
    € 10,98
      Confronta
  2. BB-VNH3SP30 - VNH3SP30 FULL BRIDGE DRIVER

    502261 BB-VNH3SP30 - VNH3SP30 FULL BRIDGE DRIVER

    BB-VNH3SP30 is full bridge driver with up to 30A and 36V working voltage. It is good to drive Gear Robot motors with reversalfalse
    Tasse escluse:
    € 9,00
    IVA inclusa:
    € 10,98
      Confronta
  3. Stepper Motor with 28cm Lead Screw: Bipolar, 200 Steps/Rev, 2.8V, 1.7 A/Phase

    342268 Stepper Motor with 28cm Lead Screw: Bipolar, 200 Steps/Rev, 2.8V, 1.7 A/Phase

    This NEMA 17-size hybrid bipolar stepping motor has an integrated 28 cm (11″) threaded rod as its output shaft, turning it infalse
    Tasse escluse:
    € 68,00
    IVA inclusa:
    € 82,96
      Confronta
  4. Big Easy Driver

    712859 Big Easy Driver

    The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase.
    Tasse escluse:
    € 16,15
    IVA inclusa:
    € 19,70
      Confronta
  5. SparkFun Servo Trigger

    713118 SparkFun Servo Trigger

    When an external switch or logic signal changes state, the Servo Trigger is able to tell an attached servo motor to move fromfalse
    Tasse escluse:
    € 16,15
    IVA inclusa:
    € 19,70
      Confronta
  6. 2971 - DRV8880 Stepper Motor Driver Carrier

    342971 2971 - DRV8880 Stepper Motor Driver Carrier

    This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurfalse
    Tasse escluse:
    € 5,84
    IVA inclusa:
    € 7,12
      Confronta
  7. EasyDriver Stepper Motor Driver

    712779 EasyDriver Stepper Motor Driver

    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or false
    Tasse escluse:
    € 10,19
    IVA inclusa:
    € 12,43
      Confronta
  8. 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller

    343131 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller

    The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Tasse escluse:
    € 65,00
    IVA inclusa:
    € 79,30
      Confronta
  9. 3132 - Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)

    343132 3132 - Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 64,00
    IVA inclusa:
    € 78,08
      Confronta
  10. 3753 - Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled)

    343753 3753 - Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled)

    This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges sfalse
    Tasse escluse:
    € 78,00
    IVA inclusa:
    € 95,16
      Confronta
  11. 3135 - Tic T500 USB Multi-Interface Stepper Motor Controller

    343135 3135 - Tic T500 USB Multi-Interface Stepper Motor Controller

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 18,81
    IVA inclusa:
    € 22,95
      Confronta
  12. 2974 - TB67S279FTG Stepper Motor Driver Carrier

    342974 2974 - TB67S279FTG Stepper Motor Driver Carrier

    Controller per motore stepper bipolare basato sul chip Toshiba TB67S279FTG. Corrente regolabile, sette risoluzioni di microstfalse
    Tasse escluse:
    € 12,50
    IVA inclusa:
    € 15,25
      Confronta
  13. 2973 - TB67S249FTG Stepper Motor Driver Carrier

    342973 2973 - TB67S249FTG Stepper Motor Driver Carrier

    Controller per motore stepper bipolare basato sul chip Toshiba TB67S279FTG. Corrente regolabile, sette risoluzioni di microstfalse
    Tasse escluse:
    € 14,00
    IVA inclusa:
    € 17,08
      Confronta
  14. 3149 - Jrk G2 24v21 USB Motor Controller with Feedback

    343149 3149 - Jrk G2 24v21 USB Motor Controller with Feedback

    Motor controller ad anello chiuso, controllo della posizione o della velocita'. Controlla un motore a spazzole. Configurabilefalse
    Tasse escluse:
    € 142,00
    IVA inclusa:
    € 173,24
      Confronta
  15. 3139 - Tic T249 USB Multi-Interface Stepper Motor Controller

    343139 3139 - Tic T249 USB Multi-Interface Stepper Motor Controller

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 28,84
    IVA inclusa:
    € 35,18
      Confronta
  16. 3730 - Pololu High-Power Stepper Motor Driver 36v4

    343730 3730 - Pololu High-Power Stepper Motor Driver 36v4

    Controllo per un motore Stepper (passo passo) con potenza max di 4A per fase (6A max*). Si configura con interfaccia SPI
    Tasse escluse:
    € 42,00
    IVA inclusa:
    € 51,24
      Confronta
  17. 2998 - TB67S128FTG Stepper Motor Driver Carrier

    342998 2998 - TB67S128FTG Stepper Motor Driver Carrier

    Controller per motore stepper bipolare basato sul chip Toshiba TB67S128FTG. Corrente regolabile, sette risoluzioni di microstfalse
    Tasse escluse:
    € 10,24
    IVA inclusa:
    € 12,49
      Confronta