Dettagli
This gearmotor is a powerful 12V brushed DC motor with a 131.25:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 8400 counts per revolution of the gearbox’s output shaft. These units have a 0.61"-long, 6 mm-diameter D-shaped output shaft.
Key specs at 12 V: 80 RPM and 300 mA free-run, 250 oz-in (18 kg-cm) and 5 A stall.
These motors are intended for use at 12 V, though in general, these kinds of motors can run at voltages above and below the nominal voltage (they can begin rotating at voltages as low as 1 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
Using the Encoder
A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 11" (28 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with standard 0.1″ male headers and our male jumper and precrimped wires. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions:
Color | Function |
---|---|
Red | motor power (connects to one motor terminal) |
Black | motor power (connects to the other motor terminal) |
Green | encoder GND |
Blue | encoder Vcc (3.5 – 20 V) |
Yellow | encoder A output |
White | encoder B output |
The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction.
Dimensions
Size: | 37D x 72.5L mm1 |
---|---|
Weight: | 235 g |
Shaft diameter: | 6 mm |
General specifications
Gear ratio: | 131:1 |
---|---|
Free-run speed @ 6V: | 40 rpm2 |
Free-run current @ 6V: | 250 mA2 |
Stall current @ 6V: | 2500 mA2 |
Stall torque @ 6V: | 125 oz·in2 |
Free-run speed @ 12V: | 80 rpm |
Free-run current @ 12V: | 300 mA |
Stall current @ 12V: | 5000 mA |
Stall torque @ 12V: | 250 oz·in |
Lead length: | 11 in |
Notes:
Specifiche
Part. No. : | 2827 |
Diam. Asse mm : | 6 |
Questions on 2827 - 131:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
420114 Motoriduttore 12Vdc 81RPM Encoder
Motoriduttore: Tensione 12 Vdc Coppia 5.1 Kg/cm 81 RPM Diametro Asse 6 mm Encoder 3 impulsi / giro -
420115 Motoriduttore 12Vdc 66RPM Encoder
Motoriduttore: Tensione 12 Vdc Coppia 6.12 Kg/cm 66 RPM Diametro Asse 6 mm Encoder 3 impulsi / giro -
420116 Motoriduttore 12Vdc 33RPM Encoder
Motoriduttore: Tensione 12 Vdc Coppia 10.2 Kg/cm 33 RPM Diametro Asse 6 mm Encoder 3 impulsi / giro -
582566 1084 - Pololu Stamped Aluminum L-Bracket Pair for 37D mm Metal Gearmotors
These aluminum gearmotor brackets let you mount Pololu’s 37D mm metal gearmotors to your project. The brackets are sold in pafalse -
342826 2826 - 100:1 Metal Gearmotor 37Dx73L mm with 64 CPR Encoder
This gearmotor is a powerful 12V brushed DC motor with a 102.083:1 metal gearbox and an integrated quadrature encoder that prfalse -
342828 2828 - 150:1 Metal Gearmotor 37Dx73L mm 12V with 64 CPR Encoder (Helical Pinion)
This gearmotor is a powerful 12V brushed DC motor with a 150:1 metal gearbox and an integrated quadrature encoder that providfalse