342973 2973 - TB67S249FTG Stepper Motor Driver Carrier

2973 - TB67S249FTG Stepper Motor Driver Carrier

Controller per motore stepper bipolare basato sul chip Toshiba TB67S279FTG. Corrente regolabile, sette risoluzioni di microstepping (fino ad 1/32). Gestione automatica del decay mode, riduce la corrente quando il motore non e' sotto sforzo. Potenza di circa 1.7A per fase
Prezzi IVA inclusa
€ 13,05 Prezzo
€ 10,70 + VAT

Qty
 

Dettagli

This breakout board makes it easy to use Toshiba’s TB67S249FTG microstepping bipolar stepper motor driver, which features adjustable current limiting and seven microstep resolutions (down to 1/32-step). In addition, it dynamically selects an optimal decay mode by monitoring the actual motor current, and it can automatically reduce the driving current below the full amount when the motor is lightly loaded to minimize power and heat. The TB67S249FTG has a wide operating voltage range of 10 V to 47 V and can deliver approximately 1.7 A per phase continuously without a heat sink or forced air flow (up to 4.5 A peak). It features built-in protection against under-voltage, over-current, and over-temperature conditions; our carrier board also adds reverse-voltage protection (up to 40 V).

This product is a carrier board or breakout board for Toshiba’s TB67S2x9FTG family of stepper motor drivers; we therefore recommend careful reading of the corresponding driver’s datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor and is available in two different versions: the TB67S249FTG can deliver about 1.7 A per phase continuously (4.5 A peak), and the TB67S279FTG can deliver about 1.2 A per phase continuously (2 A peak). (See the Power Dissipation Considerations section below for more information.)

The two versions of this stepper driver carrier look very similar, so you should consider adding your own distinguishing marks or labels if you will be working simultaneously with multiple versions. A white box is provided on the bottom silkscreen of the board to make labeling easier. This product page applies to both versions of the TB67S2x9FTG carrier.

Here are some of the board’s key features:

  • Simple step and direction control interface
  • Seven different step modes: full-step, non-circular half-step, circular half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Advanced Dynamic Mixed Decay (ADMD) dynamically switches between slow and fast decay modes by monitoring the state of current decay (not according to fixed timing)
  • Configurable Active Gain Control (AGC) automatically reduces drive current to minimize power consumption and heat generation when maximum torque is not needed
  • Motor supply voltage: 10 V to 47 V
  • Maximum continuous current per phase without additional cooling:
    • TB67S249FTG: 1.7 A (4.5 A peak)
    • TB67S279FTG: 1.2 A (2 A peak)
  • Built-in regulator (no external logic voltage supply needed)
  • Can interface directly with 3.3 V and 5 V systems
  • Under-voltage lockout and protection against over-current/short-circuit and over-temperature
  • Open-load detection
  • Active-low error outputs indicate over-current, over-temperature, or open-load condition
  • Carrier board adds reverse-voltage protection up to 40 V
  • Compact size (1.0″ × 1.4″)
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB

Details for item #2973

This version uses a TB67S249FTG driver and can deliver approximately 1.7 A per phase continuously without a heat sink or forced air flow (up to 4.5 A peak). It can be distinguished by the marking “S249FTG” on the driver IC.

For more information about this driver, please read the TB67S249FTG datasheet (533k pdf).

Included hardware

This product ships with all surface-mount components—including the TB67S2x9FTG driver IC—installed as shown in the product picture. However, soldering is required for assembly of the included through-hole parts: two 1×15-pin breakaway 0.1″ male headers and three 2-pin, 3.5 mm terminal blocks (for board power and motor outputs).

Dimensions

Size: 1.0″ × 1.4″
Weight: 4.3 g1

General specifications

Motor driver: TB67S249FTG
Minimum operating voltage: 10 V
Maximum operating voltage: 47 V
Continuous current per phase: 1.7 A
Maximum current per phase: 4.5 A
Minimum logic voltage: 2 V2
Maximum logic voltage: 5.5 V
Microstep resolutions: full, non-circular 1/2, 1/2, 1/4, 1/8, 1/16, 1/32
Current limit control: potentiometer
Reverse voltage protection?: Y3
Header pins soldered?: N

Identifying markings

PCB dev codes: md34b
Other PCB markings: 0J11196, blank white box

Notes:

1 Without included hardware.
2 This is the input logic high threshold.
3 Note: Reverse voltage protection only works up to 40 V.

Product page

Specifiche

Part. No. : 2973

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2973 - TB67S249FTG Stepper Motor Driver Carrier

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

    582133 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

    Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 1.5A per fase, fino a 2.2A con dissipatore (nfalse
    Tasse escluse:
    € 6,72
    IVA inclusa:
    € 8,20
      Confronta
  2. DRV8824 Stepper Motor Driver Carrier, Low Current

    582563 DRV8824 Stepper Motor Driver Carrier, Low Current

    Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 0.75A per fase, fino a 1.2A con dissipatore (false
    Tasse escluse:
    € 6,05
    IVA inclusa:
    € 7,38
      Confronta
  3. 2971 - DRV8880 Stepper Motor Driver Carrier

    342971 2971 - DRV8880 Stepper Motor Driver Carrier

    This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurfalse
    Tasse escluse:
    € 5,29
    IVA inclusa:
    € 6,45
      Confronta
  4. EasyDriver Stepper Motor Driver

    712779 EasyDriver Stepper Motor Driver

    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or false
    Tasse escluse:
    € 9,47
    IVA inclusa:
    € 11,55
      Confronta
  5. 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller

    343131 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller

    The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Tasse escluse:
    € 21,49
    IVA inclusa:
    € 26,22
      Confronta
  6. 2974 - TB67S279FTG Stepper Motor Driver Carrier

    342974 2974 - TB67S279FTG Stepper Motor Driver Carrier

    Controller per motore stepper bipolare basato sul chip Toshiba TB67S279FTG. Corrente regolabile, sette risoluzioni di microstfalse
    Tasse escluse:
    € 8,80
    IVA inclusa:
    € 10,74
      Confronta

Se hai trovato questo prodotto ad un prezzo migliore, inviaci una segnalazione, faremo tutto il possibile per accontentarti.

Price Match



* Campi richiesti

Il nostro Reparto Vendite rispondera' entro 24 ore via e-mail.

Grazie per la tua fiducia in Robot Italy!