Dettagli
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a TI DRV8834 driver and male headers and terminal blocks are included but not soldered. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2 A max with sufficient additional cooling)
The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces–USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial–and offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer).
The Tic family currently has two members: the Tic T825, which operates from 8.5 V to 45 V, and the Tic T834, which operates from 2.5 V to 10.8 V. Both can deliver up to 1.5 A continuous per phase without a heat sink or forced air flow.
Features and specifications
- Open-loop speed or position control of one bipolar stepper motor
- A variety of control interfaces:
- USB for direct connection to a computer
- TTL serial operating at 5 V for use with a microcontroller
- I²C for use with a microcontroller
- RC hobby servo pulses for use in an RC system
- Analog voltage for use with a potentiometer or analog joystick
- Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (not for position feedback)
- STEP/DIR inputs for compatibility with existing stepper motor control firmware
- Acceleration and deceleration limiting
- Maximum stepper speed: 50,000 steps per second
- Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).
- Six different microstep resolutions: full step, half step, 1/4 step, 1/8 step, 1/16 step, and 1/32 step
- Digitally adjustable current limit
- Optional safety controls to avoid unexpectedly powering the motor
- Input calibration (learning) and adjustable scaling degree for analog and RC signals
- 5 V regulator (no external logic voltage supply needed)
- Optional kill switch inputs
- Connects to a computer through USB via a USB A to Micro-B cable (not included)
- Free configuration software available for Windows, Linux, and macOS
- Comprehensive user’s guide
Details for item #3132
The Tic T834 is based on the DRV8834 IC from Texas Instruments. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A continuous per phase without a heat sink or forced air flow (the peak current per phase is 2 A). This version is sold with connectors soldered so no soldering is necessary to use it.
Dimensions
Size: | 1.50″ × 1.05″ × 0.42″1 |
---|---|
Weight: | 5.1 g1 |
General specifications
Model: | Tic T834 |
---|---|
Motor driver: | DRV8834 |
Control interface: | USB; non-inverted TTL serial; I²C; RC servo pulses; analog voltage; quadrature encoder |
Minimum operating voltage: | 2.5 V |
Maximum operating voltage: | 10.8 V |
Continuous current per phase: | 1.5 A2 |
Maximum current per phase: | 2 A3 |
Maximum step rate: | 50000 PPS |
Microstep resolutions: | full, 1/2, 1/4, 1/8, 1/16, and 1/32 |
Reverse voltage protection?: | Y |
Header pins soldered: | Y |
Identifying markings
PCB dev codes: | tic02a |
---|---|
Other PCB markings: | 0J10607 |
Notes:
Specifiche
Part. No. : | 3132 |
Questions on 3132 - Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)
-
02/08/18 19.19 Buonasera sono interessato questo controller per realizzare un inseguitore astronomico.Non riesco capire se può raggiungere una velocità minima di 1,15 arcosecondi
- Salve, questo controller riesce a gestire 1/32 di step. Considerando un motore con 200 step per giro, e' possibile controllare 200x32= 6400 step per un giro completo del motore. La risoluzione puo' essere ulteriormente aumentata introducendo sistemi di demoltiplica (riduttore, vite senza fine, etc). Questa e' una pratica quasi obbligatoria in quanto il solo motore normalmente non ha la forza sufficiente a fare il lavoro. Saluti
- Do you find this question helpful? Si No
Prodotti correlati
-
582133 2133 - DRV8825 Stepper Motor Driver Carrier, High Current
Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 1.5A per fase, fino a 2.2A con dissipatore (nfalse -
342971 2971 - DRV8880 Stepper Motor Driver Carrier
This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurfalse -
712779 EasyDriver Stepper Motor Driver
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or false -
343131 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller
The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse -
343135 3135 - Tic T500 USB Multi-Interface Stepper Motor Controller
Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse -
342974 2974 - TB67S279FTG Stepper Motor Driver Carrier
Controller per motore stepper bipolare basato sul chip Toshiba TB67S279FTG. Corrente regolabile, sette risoluzioni di microstfalse -
343139 3139 - Tic T249 USB Multi-Interface Stepper Motor Controller
Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse -
343730 3730 - Pololu High-Power Stepper Motor Driver 36v4
Controllo per un motore Stepper (passo passo) con potenza max di 4A per fase (6A max*). Si configura con interfaccia SPI -
343140 3140 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller (Connectors Soldered)
Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse -
343141 3141 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller
Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse