The Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a discrete MOSFET stepper motor driver, and it ships with soldered header pins and terminal blocks. It can operate from 8 V to 50 V and can deliver up to approximately 4 A per phase without a heat sink or forced air flow (or 6 A max with sufficient additional cooling).
The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial. They also offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer).
Features and specifications
- Open-loop speed or position control of one bipolar stepper motor
- A variety of control interfaces:
- USB for direct connection to a computer
- TTL serial operating at 5 V for use with a microcontroller
- I²C for use with a microcontroller
- RC hobby servo pulses for use in an RC system
- Analog voltage for use with a potentiometer or analog joystick
- Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (not for position feedback)
- STEP/DIR inputs for compatibility with existing stepper motor control firmware
- Acceleration and deceleration limiting
- Maximum stepper speed: 50,000 steps per second
- Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).
- Selectable microstep modes up to 1/256-step resolution:
- The Tic 36v4 supports full-step to 1/256-step modes
- The Tic T825, Tic T834, and T249 support full-step to 1/32-step modes
- The Tic T500 supports full-step to 1/8-step modes
- Digitally adjustable current limit
- Optional safety controls to avoid unexpectedly powering the motor
- Input calibration (learning) and adjustable scaling degree for analog and RC signals
- 5 V regulator (no external logic voltage supply needed)
- Optional limit switch inputs with homing capabilities
- Optional kill switch inputs
- STEP/DIR outputs for controlling external stepper motor drivers
- Connects to a computer through USB via a USB A to Micro-B cable (not included)
- Free configuration software available for Windows, Linux, and macOS
- Arduino library makes it easy to get started using these controllers with an Arduino or compatible board
- Comprehensive user’s guide
|Size:||1.50″ × 1.05″ × 0.47″|
|Motor driver:||discrete MOSFETs|
|Control interface:||USB; non-inverted TTL serial; I²C;
RC servo pulses; analog voltage; quadrature encoder
|Minimum operating voltage:||8 V|
|Maximum operating voltage:||50 V1|
|Continuous current per phase:||4 A2|
|Maximum current per phase:||6 A3|
|Maximum step rate:||50000 PPS|
|Microstep resolutions:||full, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, and 1/256|
|Reverse voltage protection?:||Y4|
|PCB dev codes:||tic06a|
|Other PCB markings:||0J12451|
- 1 Reverse voltage protection only works up to 40 V.
- 2 Without a heat sink or forced air flow.
- 3 With sufficient additional cooling.
- 4 To -40 V. Connecting supplies over 40 V in reverse can damage the device.
|Part. No. :||3141|
Questions on 3141 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller
No questions asked yetFai una domanda (Registrati oppure Esegui il Login ).
Tasse escluse:€ 24,36IVA inclusa:€ 29,72
Tasse escluse:€ 25,96IVA inclusa:€ 31,67
Tasse escluse:€ 18,81IVA inclusa:€ 22,95
Tasse escluse:€ 28,84IVA inclusa:€ 35,18
Tasse escluse:€ 16,02IVA inclusa:€ 19,54
Tasse escluse:€ 48,56IVA inclusa:€ 59,24