This NEMA-23 motor has an integrated Planetary gearbox with a
76 49/64 :1 ratio. It comes with the rear shaft exposed, so you can mount an encoder or shaft coupler.
When connected to a 1067 - PhidgetStepper Bipolar HC, the 3334 has a maximum speed of 25 RPM. At the output of the gearbox, the step angle approximately 0.023°. When using the step angle in calculations, you should derive the exact step angle by dividing 1.8° by the gearbox reduction ratio.
At 2.8 Amps, this stepper motor can produce a maximum torque of 960 kg-cm. However, the gearbox is only rated for 240 kg-cm of continuous torque. Loading this gearbox stepper beyond the torque rating of the gearbox will shorten its useful life.
The 3334 stepper motor connects to a bipolar motor controller such as the 1067 - PhidgetStepper Bipolar HC.
The following table shows how to connect the motor wires to the board connectors to produce a clockwise rotation in the stepper motor when increasing position. To wire for counter-clockwise rotation when increasing position, reverse the red and blue wires.
Note: Make sure to unplug the power cord from the motor controller before switching wires around.
The rear shaft of this motor can be equipped with the HKT22 Optical Encoder for applications where you need to keep track of the exact position, velocity, or acceleration of the motor.
|Motor Type||Bipolar Stepper|
|Manufacturer Part Number||57STH56-2804B / 56JXS300K77|
|Step Accuracy||± 5 %|
|Holding Torque||240 kg·cm|
|Rated Torque||240 kg·cm|
|Maximum Speed (w/1067 Motor Controller)||25 RPM|
|Acceleration at Max Speed
(w/1067 Motor Controller)
|1E+06 1/16 steps/sec²|
|Recommended Voltage||12 V DC|
|Rated Current||2.8 A|
|Coil Resistance||900 mΩ|
|Shaft Diameter||12 mm|
|Rear Shaft Diameter||3.9 mm|
|Mounting Plate Size||NEMA - 23|
|Number of Leads||4|
|Wire Length||300 mm|
|Gear Ratio||76 49⁄64 : 1|
|Backlash Error||1 1⁄2°|
|Maximum Strength of Gears||240 kg·cm|
|Shaft Maximum Axial Load||100 N|
|Shaft Maximum Radial Load||250 N|
Connecting the motor directly to a power supply will destroy the motor and void the warranty. If you want to check your motor make sure it is connected to a constant current / chopper drive controller.
|Part. No. :||3334|
|Diam. Asse mm :||12|
Questions on 3334 - 57STH56 NEMA-23 Bipolar Stepper with 77:1 Gearbox
No questions asked yetFai una domanda (Registrati oppure Esegui il Login ).
193331 3331 - 57STH56 NEMA-23 Bipolar Gearless StepperThis high-speed bipolar stepper with a rear shaft has a 1.8° step angle and 11 kg·cm of torque at low speeds.Tasse escluse:€ 25,54IVA inclusa:€ 31,16
193531 3531 - Optical Rotary Encoder HKT22This low-cost encoder is designed to fit on the rear shaft of our stepper motors. Measure the rotation of your motor even whefalseTasse escluse:€ 31,02IVA inclusa:€ 37,84
193339 3339 - Stepper Mounting Bracket (NEMA 23)Fix a NEMA-23 sized motor or 56mm gearbox to a flat surface with this steel mounting bracket.Tasse escluse:€ 5,43IVA inclusa:€ 6,62
120349 Bipolar Stepper Motor with Planet Gear Box (18kg.cm)This bipolar stepper motor with planet gear box (gear ratio: 5.18) uses a standard 8mm-diameter D type output shaft, and has falseTasse escluse:€ 37,20IVA inclusa:€ 45,38