This is the Feather 32u4 Basic Proto, it has a bunch of prototyping space built right in We have other boards in the Feather family, check'em out here!
At the Feather 32u4's heart is at ATmega32u4 clocked at 8 MHz and at 3.3V logic, a chip setup we've had tons of experience with as it's the same as the Flora. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. This chip is well supported in the Arduino IDE and can run just about every sensor/library out there.
To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.
Here's some handy specs!
- Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
- Light as a (large?) feather - 4.8 grams
- ATmega32u4 @ 8MHz with 3.3V logic/power
- 3.3V regulator with 500mA peak current output
- USB native support, comes with USB bootloader and serial port debugging
- You also get tons of pins - 20 GPIO pins
- Hardware Serial, hardware I2C, hardware SPI support
- 8 x PWM pins
- 10 x analog inputs (one is used to measure the battery voltage)
- Built in 100mA lipoly charger with charging status indicator LED
- Pin #13 red LED for general purpose blinking
- Power/enable pin
- 4 mounting holes
- Reset button
The Feather 32u4 Basic Proto has some extra space left over, so we give you a tiny little prototyping area. If you just need to attach a button or sensor, you may be able to skip out on a breadboard and wire it directly on there.
Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)
Check out our tutorial for all sorts of details, including schematics, files, IDE instructions, and more!
- 51mm x 23mm x 8mm / 2.0" x 0.9" x 0.28"
- Weight: 4.8g
|Part. No. :||2771|
Questions on Adafruit Feather 32u4 Basic Proto
No questions asked yetFai una domanda (Registrati oppure Esegui il Login ).
808524 Adafruit Feather 32u4 Bluefruit LEThis is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with builfalseTasse escluse:€ 31,84IVA inclusa:€ 38,84
808529 FeatherWing Proto - Prototyping Add-on For All Feather BoardsThis is the FeatherWing Proto - a prototyping add-on for all Feather boards.Tasse escluse:€ 5,47IVA inclusa:€ 6,67
808553 Adafruit Feather 32u4 AdaloggerThis is the Adafruit Feather 32u4 Adalogger - our take on an 'all-in-one' datalogger (or data-reader) with built in USB and bfalseTasse escluse:€ 20,52IVA inclusa:€ 25,03
808554 Feather Stacking Headers - 12-pin and 16-pin female headersThese two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!Tasse escluse:€ 1,79IVA inclusa:€ 2,18
808581 8-Channel PWM or Servo FeatherWing Add-on For All Feather BoardsThis is the 8-Channel PWM or Servo FeatherWing, you can add 8 x 12-bit PWM outputs to your FeatherWing.Tasse escluse:€ 9,44IVA inclusa:€ 11,52
808884 OLED Breakout Board - 16-bit Color 1.5" w/microSD holderThis OLED uses the SSD1351 driver chip, which manages the display. You can talk to the driver chip using 4-wire write-only SPfalseTasse escluse:€ 37,17IVA inclusa:€ 45,35
809083 Adafruit AMG8833 IR Thermal Camera FeatherWingThis is the Thermal Camera FeatherWing: thanks to the Panasonic AMG8833 8x8 GridEYE sensor, it adds heat-vision to any FeathefalseTasse escluse:€ 44,80IVA inclusa:€ 54,66
809084 Adafruit DotStar FeatherWing - 6 x 12 RGB LEDsThis is the DotStar FeatherWing, a 6x12 RGB LED Add-on For All Feather Boards!Tasse escluse:€ 31,84IVA inclusa:€ 38,84