808524 Adafruit Feather 32u4 Bluefruit LE

Adafruit Feather 32u4 Bluefruit LE

This is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather 32u4 with a BTLE module, ready to rock!
Prezzi IVA inclusa
€ 38,84 Prezzo
€ 31,84 + VAT

 

Dettagli

Feather is the new development board from Adafruit, and like it's namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

This is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather 32u4 with a BTLE module, ready to rock! Bluetooth Low Energy is the hottest new low-power, 2.4GHz spectrum wireless protocol. In particular, its the only wireless protocol that you can use with iOS without needing special certification and it's supported by all modern smart phones. This makes it excellent for use in portable projects that will make use of an iOS or Android phone or tablet. It also is supported in Mac OS X and Windows 8+.

At the Feather 32u4's heart is at ATmega32u4 clocked at 8 MHz and at 3.3V logic, a chip setup we've had tons of experience with as it's the same as the Flora. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc.

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.

Here's some handy specs! Like all Feather 32u4's you get:

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 5.7 grams
  • ATmega32u4 @ 8MHz with 3.3V logic/power
  • 3.3V regulator with 500mA peak current output
  • USB native support, comes with USB bootloader and serial port debugging
  • You also get tons of pins - 20 GPIO pins
  • Hardware Serial, hardware I2C, hardware SPI support
  • 8 x PWM pins
  • 10 x analog inputs
  • Built in 100mA lipoly charger with charging status indicator LED
  • Pin #13 red LED for general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

The Feather 32u4 Bluefruit LE uses the extra space left over to add our excellent Bluefruit BTLE module + two status indicator LEDs.

The Power of Bluefruit LE

The Bluefruit LE module is an nRF51822 chipset from Nordic, programmed with multi-function code that can do quite a lot! For most people, they'll be very happy to use the standard Nordic UART RX/TX connection profile. In this profile, the Bluefruit acts as a data pipe, that can 'transparently' transmit back and forth from your iOS or Android device. You can use our iOS App or Android App, or write your own to communicate with the UART service.

The board is capable of much more than just sending strings over the air!  Thanks to an easy to learn AT command set, you have full control over how the device behaves, including the ability to define and manipulate your own GATT Services and Characteristics, or change the way that the device advertises itself for other Bluetooth Low Energy devices to see. You can also use the AT commands  to query the die temperature, check the battery voltage, and more, check the connection RSSI or MAC address, and tons more. Really, way too long to list here!

Use the Bluefruit App to get your project started

Using our Bluefruit iOS App or Android App, you can quickly get your project prototyped by using your iOS or Android phone/tablet as a controller. We have a color picker,quaternion/accelerometer/gyro/magnetometer or location (GPS), and an 8-button control game pad. This data can be read over BLE and piped into the ATmega32u4 chip for processing & control

You can do a lot more too!

  • The Bluefruit can also act like an HID Keyboard (for devices that support BLE HID)
  • Can become a BLE Heart Rate Monitor (a standard profile for BLE) - you just need to add the pulse-detection circuitry
  • Turn it into a UriBeacon, the Google standard for Bluetooth LE beacons. Just power it and the 'Friend will bleep out a URL to any nearby devices with the UriBeacon app installed.
  • Built in over-the-air bootloading capability so we can keep you updated with the hottest new firmware. Use any Android or iOS device to get updates and install them. This will update the native code on the BLE module, to add new wireless capabilities, not program the ATmega chip.

Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and MicroUSB cable not included (but we do have lots of options in the shop if you'd like!)

Check out our tutorial for all sorts of details, including schematics, files, IDE instructions, and more!

Specifiche

Part. No. : 2829

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit Feather 32u4 Bluefruit LE

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Bluetooth V4.0 HM-11 BLE Module

    807809 Bluetooth V4.0 HM-11 BLE Module

    This is a SMD BLE module used in our BLE Bee and Xadow BLE. It is based on TI cc2541 chip, enables robust network nodes to befalse
    Tasse escluse:
    € 12,16
    IVA inclusa:
    € 14,84
      Confronta
  2. Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v1.0

    808149 Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v1.0

    This Bluefruit LE Friend is programmed with a special firmware image that turns it into an easy to use Bluetooth Low Energy sfalse
    Tasse escluse:
    € 26,57
    IVA inclusa:
    € 32,42
      Confronta
  3. PTR9022 Multiprotocol ANT/BLE Module embedded ARM Cortex

    808350 PTR9022 Multiprotocol ANT/BLE Module embedded ARM Cortex

    eNet-ZBP113 ZigBee module is a 2.4-GHz, IEEE 802.15.4/ZigBee embedded wireless module built in TICC2530, designed by BestU. efalse
    Tasse escluse:
    € 7,99
    IVA inclusa:
    € 9,75
      Confronta
  4. BLE(dual model) Bee

    808352 BLE(dual model) Bee

    BLE (dual) Bee v1.0 uses CSR dual mode Bluetooth chip,with the ARM architecture single chip which supports AT instructions, Ufalse
    Tasse escluse:
    € 19,06
    IVA inclusa:
    € 23,25
      Confronta
  5. FeatherWing Proto - Prototyping Add-on For All Feather Boards

    808529 FeatherWing Proto - Prototyping Add-on For All Feather Boards

    This is the FeatherWing Proto - a prototyping add-on for all Feather boards.
    Tasse escluse:
    € 5,47
    IVA inclusa:
    € 6,67
      Confronta
  6. Adafruit Feather 32u4 Adalogger

    808553 Adafruit Feather 32u4 Adalogger

    This is the Adafruit Feather 32u4 Adalogger - our take on an 'all-in-one' datalogger (or data-reader) with built in USB and bfalse
    Tasse escluse:
    € 20,52
    IVA inclusa:
    € 25,03
      Confronta
  7. Feather Stacking Headers - 12-pin and 16-pin female headers

    808554 Feather Stacking Headers - 12-pin and 16-pin female headers

    These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!
    Tasse escluse:
    € 1,79
    IVA inclusa:
    € 2,18
      Confronta
  8. Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500

    808602 Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500

    This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFfalse
    Tasse escluse:
    € 37,12
    IVA inclusa:
    € 45,29
      Confronta
  9. Short Feather Headers Kit - 12-pin and 16-pin Female Header Set

    808604 Short Feather Headers Kit - 12-pin and 16-pin Female Header Set

    These two Short Female Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!
    Tasse escluse:
    € 2,09
    IVA inclusa:
    € 2,55
      Confronta
  10. Adalogger FeatherWing - RTC + SD Add-on For All Feather Boards

    808615 Adalogger FeatherWing - RTC + SD Add-on For All Feather Boards

    This FeatherWing will make it real easy to add datalogging to any of our existing Feathers. You get both an I2C real time clofalse
    Tasse escluse:
    € 10,00
    IVA inclusa:
    € 12,20
      Confronta
  11. DS3231 Precision RTC FeatherWing - RTC Add-on For Feather Boards

    808616 DS3231 Precision RTC FeatherWing - RTC Add-on For Feather Boards

    This is the DS3231 Precision RTC FeatherWing: it adds an extremely accurate I2C-integrated Real Time Clock (RTC) with a Tempefalse
    Tasse escluse:
    € 13,14
    IVA inclusa:
    € 16,03
      Confronta
  12. Adafruit Feather 32u4 FONA

    808618 Adafruit Feather 32u4 FONA

    This is the Adafruit Feather 32u4 FONA - our take on an 'all-in-one' Arduino-compatible + audio/sms/data capable cellular witfalse
    Tasse escluse:
    € 47,67
    IVA inclusa:
    € 58,16
      Confronta
  13. Adafruit ATWINC1500 WiFi Breakout with uFL Connector - fw 19.4.4

    808655 Adafruit ATWINC1500 WiFi Breakout with uFL Connector - fw 19.4.4

    This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performfalse
    Tasse escluse:
    € 23,28
    IVA inclusa:
    € 28,40
      Confronta
  14. Adafruit Feather M0 RFM69 Packet Radio - 433MHz

    808729 Adafruit Feather M0 RFM69 Packet Radio - 433MHz

    This is the Adafruit Feather M0 RFM69 Packet Radio (433 MHz) - our take on an microcontroller with a RFM69 HCW packet radio tfalse
    Tasse escluse:
    € 26,57
    IVA inclusa:
    € 32,42
      Confronta
  15. Feather 0.1" Pitch Terminal Blocks

    808731 Feather 0.1" Pitch Terminal Blocks

    These 0.1" Pitch Terminal Blocks, are exactly the right size to it your Feather board or FeatherWing. They are great newfalse
    Tasse escluse:
    € 5,74
    IVA inclusa:
    € 7,00
      Confronta
  16. Assembled Adafruit Feather HUZZAH with ESP8266 WiFi With Headers

    808914 Assembled Adafruit Feather HUZZAH with ESP8266 WiFi With Headers

    This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB anfalse
    Tasse escluse:
    € 20,25
    IVA inclusa:
    € 24,71
      Confronta
  17. Adafruit Feather M0 Express - Designed for CircuitPython - ATSAMD21 Cortex M0

    808966 Adafruit Feather M0 Express - Designed for CircuitPython - ATSAMD21 Cortex M0

    We love all our Feathers equally, but this Feather is very special. It's our first Feather that is specifically designed for false
    Tasse escluse:
    € 21,30
    IVA inclusa:
    € 25,99
      Confronta
  18. Adafruit Feather nRF52 Bluefruit LE - nRF52832

    808974 Adafruit Feather nRF52 Bluefruit LE - nRF52832

    The Adafruit Feather nRF52 Bluefruit is our latest easy-to-use all-in-one Bluetooth Low Energy board, with a native-bluetoothfalse
    Tasse escluse:
    € 26,57
    IVA inclusa:
    € 32,42
      Confronta
  19. Adafruit INA219 FeatherWing

    809082 Adafruit INA219 FeatherWing

    Instead of struggling with two multimeters, you can just use the handy INA219B chip on this breakout to both measure both thefalse
    Tasse escluse:
    € 8,64
    IVA inclusa:
    € 10,54
      Confronta