808916 Adafruit TPL5110 Low Power Timer Breakout

Adafruit TPL5110 Low Power Timer Breakout

The Adafruit TPL5110 Power Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of turning your project on/off using a built in timer that can vary from once every 100ms up to once every two hours
Prezzi IVA inclusa
€ 7,32 Prezzo
€ 6,00 + VAT

 

Dettagli

With some development boards, low power usage is an afterthought. Especially when price and usability is the main selling point. So what should you do when it's time to turn around and make that project of yours run on a battery or solar? Sure you could try to hot-air that regulator off, or you could jerry-rig a relay. Or, use a 555? Ugh, the options aren't that great.

The Adafruit TPL5110 Power Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of turning your project on/off using a built in timer that can vary from once every 100ms up to once every two hours. Basically, the TPL will turn on periodically, adjustable by potentiometer or resistor, and turn on your project's power. It will then wait until a signal is received from the project to tell the TPL that it can safely turn off the power.

Usage is easy. First, set your desired delay by adjusting the on-board trim pot: nearly-all-the-way-to-the-left is "once per 100ms" and all-the-way-to-the-right is "once every 2 hours". Then, connect VDD up to your 3-5V power supply and then your project's power-in to the Drive pin. Finally, select a signal pin from your project to the Done pin. In your project's code or design, just make sure that it sets the Done pin high once it is completed with its task. That's it!

While the TPL5110 is running (but the remainder of the project is de-powered) the current draw is about 20uA (according to our Monsoon Power Meter).

If you want to turn the device on by hand, you can also activate the TPL by pressing the onboard tactile switch (or wire your own switch to the Delay pin). See? Your power problems just got solved!

Comes as a fully assembled breakout board with a TPL5110 chip, all components on-board, and some header. A little light soldering is required to put it together for breadboard use.

For usage video, code, libraries, wiring examples, CAD files, Fritzing and more, check out the guide!

Product Dimensions: 19.3mm x 18.0mm x 4.5mm / 0.8" x 0.7" x 0.2"

Product Weight: 1.3g / 0.0oz

 

Specifiche

Part. No. : 3435

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on Adafruit TPL5110 Low Power Timer Breakout

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. Metal Pushbutton - Momentary (16mm, Yellow)

    711969 Metal Pushbutton - Momentary (16mm, Yellow)

    Pulsante in metallo illuminato. Giallo.
    Tasse escluse:
    € 6,87
    IVA inclusa:
    € 8,38
      Confronta
  2. 2812 - Big Pushbutton Power Switch with Reverse Voltage Protection, MP

    342812 2812 - Big Pushbutton Power Switch with Reverse Voltage Protection, MP

    The Pololu Pushbutton Power Switches are sophisticated power control alternatives to bulky mechanical switches.
    Tasse escluse:
    € 4,97
    IVA inclusa:
    € 6,06
      Confronta
  3. Mini Illuminated Momentary Pushbutton - Red Power Symbol

    808721 Mini Illuminated Momentary Pushbutton - Red Power Symbol

    This Mini Illuminated Momentary Power Button is an adorable breadboard-friendly tactile switch that has a built-in LED. It prfalse
    Tasse escluse:
    € 2,90
    IVA inclusa:
    € 3,54
      Confronta