Dettagli
A Feather board without ambition is a Feather board without FeatherWings! This is the 8-Channel PWM or Servo FeatherWing, you can add 8 x 12-bit PWM outputs to your FeatherWing. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight!
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. What now? You could give up OR you could just get our handy PWM and Servo FeatherWing. It's a lot like our popular PWM/Servo Shield but with half the channels & squished into a nice small portable size and works with any of our Feather boards.
Since the FeatherWing only uses the I2C (SDA & SCL pins), it works with any and all Feathers- ATmega32u4, ATSAM M0 or ESP8266-based. You can stack it with any other FeatherWing or with itself (just make sure you have each wing with a unique I2C address)
Specs:
- There's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
- It is 5V compliant, which means you can control it from a 3.3V Feather and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
- 6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
- Configurable push-pull or open-drain output
We wrapped up this lovely chip into a FeatherWing with a couple nice extras:
- Terminal block for power input (or you can use the 0.1" breakouts on the side)
- Reverse polarity protection on the terminal block input
- Green power-good LED
- Two groups of 4 outputs on either side, 8 total.
- Stackable design. You'll need to pick up stacking headers and right angle 3x4 headers in order to stack on top of this shield without the servo connections getting in the way.
- A spot to place a big capacitor on the V+ line (in case you need it)
- 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
- Solder jumpers for the 6 address select pins
This product comes with a fully tested and assembled wing as well as 2 pieces of 3x4 male straight header (for servo/LED plugs), a 2-pin terminal block (for power) and a stick of 0.1" header so you can plug into a Feather. A little light soldering will be required to assemble and customize the board by attaching the desired headers but it is a 15 minute task that even a beginner can do.
-
- PCA9685 datasheet
- Dimensions: 50.8mm x 22.9mm x 1.6mm / 2" x 0.9" x 0.06"
- Weight: 3.9g
Specifiche
Part. No. : | 2928 |
Questions on 8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
808524 Adafruit Feather 32u4 Bluefruit LE
This is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with builfalse -
808529 FeatherWing Proto - Prototyping Add-on For All Feather Boards
This is the FeatherWing Proto - a prototyping add-on for all Feather boards. -
808553 Adafruit Feather 32u4 Adalogger
This is the Adafruit Feather 32u4 Adalogger - our take on an 'all-in-one' datalogger (or data-reader) with built in USB and bfalse -
808554 Feather Stacking Headers - 12-pin and 16-pin female headers
These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! -
808582 DC Motor + Stepper FeatherWing Add-on For All Feather Boards
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motorx (or 1 false -
808602 Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500
This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFfalse -
808615 Adalogger FeatherWing - RTC + SD Add-on For All Feather Boards
This FeatherWing will make it real easy to add datalogging to any of our existing Feathers. You get both an I2C real time clofalse -
808914 Assembled Adafruit Feather HUZZAH with ESP8266 WiFi With Headers
This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB anfalse -
808966 Adafruit Feather M0 Express - Designed for CircuitPython - ATSAMD21 Cortex M0
We love all our Feathers equally, but this Feather is very special. It's our first Feather that is specifically designed for false -
808974 Adafruit Feather nRF52 Bluefruit LE - nRF52832
The Adafruit Feather nRF52 Bluefruit is our latest easy-to-use all-in-one Bluetooth Low Energy board, with a native-bluetoothfalse -
809082 Adafruit INA219 FeatherWing
Instead of struggling with two multimeters, you can just use the handy INA219B chip on this breakout to both measure both thefalse