120125 DFRduino Ethernet Shield V2.1 (Support Mega and Micro SD)

DFRduino Ethernet Shield V2.1 (Support Mega and Micro SD)

The DFRduino Ethernet Shield V2.1 is now released. This version of Ethernet Shield is not only compatible with Mega 1280 and 2560, but also provides a Micro SD card slot for reading/writing.
Categorie
Prezzi IVA inclusa
€ 16,34 Prezzo
€ 13,39 + VAT

 

Dettagli

The DFRduino Ethernet Shield V2.1 is now released. This version of Ethernet Shield is not only compatible with Mega 1280 and 2560, but also provides a Micro SD card slot for reading/writing.  

DFRduino Ethernet Shield V2.1 is fully compatible with Ardunio Ethernet Shield. With the offical ethernet library, you can do exactly the same thing as the original one, but at a more affordable price. 

This Ethernet Shield provides an Arduino controller board with internet access. It is based on the Wiznet W5100 ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. You can use the Ethernet library to write sketches which connect to the internet using the shield.

You can connect the Ethernet Shield to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

Arduino uses digital pins 10, 11, 12, and 13 (SPI) to communicate with the W5100 on the ethernet shield. These pins cannot be used for general i/o.

The shield provides a standard RJ45 ethernet jack.

The reset button on the shield resets both the W5100 and the Arduino board.

The shield contains a number of informational LEDs:

  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected 
 

Compatibility

  • Arduino Mega 1280/2560
  • Arduino UNO
  • Arduino Dumlinove

 

 

 

DOCUMENTS

 

 

 

 

 

SHIPPING LIST

 

 

  • DFRduino Ethernet Shield x1

Specifiche

Part. No. : DFR0125
Interfaccia : SPI
Tensione : 5
Tipo Shield : Comunicazione, Ethernet

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on DFRduino Ethernet Shield V2.1 (Support Mega and Micro SD)

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. ProtoScrewShield v1.5

    709729 ProtoScrewShield v1.5

    Il ProtoScrewShield estende tutti i pin della scheda Arduino e li rende disponibili tramite morsetti con passo 3.5mm
    Tasse escluse:
    € 15,82
    IVA inclusa:
    € 19,30
      Confronta
  2. Screw Shield

    115073 Screw Shield

    Lo Screw Shield estende i connettori di Arduino e pur conservando la possibilita' di aggiungere altri shield sopra la scheda,false
    Tasse escluse:
    € 8,20
    IVA inclusa:
    € 10,00
      Confronta
  3. Proto-Screwshield (Wingshield) R3 Kit for Arduino

    807888 Proto-Screwshield (Wingshield) R3 Kit for Arduino

    The next generation Proto-ScrewShield is a dual-purpose prototyping shield. Now only does it have a large 0.1" grid protfalse
    Tasse escluse:
    € 16,80
    IVA inclusa:
    € 20,50
    A partire da:
    € 13,42
      Confronta
  4. W5500 Ethernet with POE IOT Board (Arduino Compatible

    121300 W5500 Ethernet with POE IOT Board (Arduino Compatible

    W5500 Ethernet with POE Mainboard is a new member in our Ethernet family. It is based on the ATmega32u4 and W5500 Ethernet chfalse
    Tasse escluse:
    € 43,36
    IVA inclusa:
    € 52,90
      Confronta