Dettagli
This small synchronous switching step-down (or buck) regulator takes an input voltage from 4 V to 36 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″ yet delivers typical continuous output currents between 2 A and 2.6 A, depending on the input voltage, which makes this regulator well suited for powering moderate loads like sensors or small motors. An optional enable input can be used to put the regulator in a low-power state with a current draw of 5 µA to 10 µA per volt on VIN. The regulator also features reverse voltage protection and a power-good output indicates when the regulator cannot adequately maintain the output voltage.
The D24V22Fx family of step-down voltage regulators generates lower output voltages from input voltages as high as 36 V. They are synchronous switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) with typical efficiencies of 85% to 95%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators can typically support continuous output currents between 1.4 A and 2.6 A, though the actual available output current is a function of the input voltage and efficiency (see the Typical efficiency and Maximum continuous output current sections below). In general, the available output current is a little higher for the lower-voltage versions than it is for the higher-voltage versions, and it decreases as the input voltage increases.
These regulators have a typical quiescent (no load) current draw of around 1 mA, and an enable pin can be used to put the boards in a low-power state that reduces the quiescent current to approximately 5 µA to 10 µA per volt on VIN.
The modules have built-in reverse-voltage protection, short-circuit protection, a thermal shutdown feature that helps prevent damage from overheating, and a soft-start feature that reduces inrush current.
Features
- Input voltage:
- 4 V to 36 V for the version that outputs 3.3 V
- [output voltage + dropout voltage] to 36 V for output voltages of 5 V and higher (see the dropout voltage section for details)
- Fixed 3.3 V, 5 V, 6 V, 7.5 V, 9 V, or 12 V output (depending on regulator version) with 4% accuracy
- Typical maximum continuous output currents between 1.4 A abd 2.6 A (see the maximum continuous output current graph below)
- Typical efficiency of 85% to 95%, depending on input voltage, output voltage, and load (see the efficiency graph below)
- Switching frequency: ~400 kHz
- Integrated reverse-voltage protection, over-current and short-circuit protection, over-temperature shutoff, and soft-start
- 1 mA typical no-load quiescent current; this can be reduced to approximately 5 µA to 10 µA per volt on VIN by disabling the board (see the quiescent current graph below)
- “Power good” output indicates when the regulator cannot adequately maintain the output voltage
- Compact size: 0.7″ × 0.7″ × 0.31″ (17.8 mm × 17.8 mm × 8 mm)
- Two 0.086″ mounting holes for #2 or M2 screws
Dimensions
Size: | 0.7″ × 0.7″ × 0.31″1 |
---|---|
Weight: | 2.3 g1 |
General specifications
Minimum operating voltage: | 4 V |
---|---|
Maximum operating voltage: | 36 V |
Continuous output current: | 2.3 A2 |
Output voltage: | 3.3 V |
Reverse voltage protection?: | Y |
Maximum quiescent current: | 1 mA3 |
Identifying markings
PCB dev codes: | reg19a |
---|---|
Other PCB markings: | 0J9251 |
Notes:
- 1
- Without included optional headers.
- 2
- Typical continuous output current at 24 V in. Actual achievable continuous output current is a function of input voltage and is limited by thermal dissipation. See the output current graph under the description tab for more information.
- 3
- Quiescent current is typically under 1 mA for most of the operating range. The ENABLE pin can be used to reduce the quiescent current to less than 10 μA per volt on VIN.
Specifiche
Part. No. : | 2857 |
Interfaccia : | n/a |
Questions on 2857 - Pololu 3.3V, 2.6A Step-Down Voltage Regulator D24V22F3
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
220003 Regolatore di tensione L7805CV
Contenitore TO220. Dovunque serva una tensione stabile di 5V con una corrente Max di 1A, con l'aggiunta di un paio di condensfalse -
710967 NCP1402 Regolatore 3.3V step-up
Regolatore DC-DC step-up 3.3. Accetta in ingresso una tensione tra 1 e 3V e fornisce in uscita 3.3V. 200mA -
582119 2119 - Pololu Step-Up/Step-Down Voltage Regulator S7V7F5
Regolatore DC, accetta tensioni da 2,7 a 11,8VDC in ingresso e produce 5VDC in uscita. Utile in casi in cui la tensione in infalse -
582504 2098 - Pololu 5V, 300mA Step-Down Voltage Regulator D24V3F5
Regolatore DC, accetta tensioni fino a 42VDC in ingresso e produce 5VDC in uscita. Potenza max 300mA -
582505 2121 - Pololu 5V Step-Up/Step-Down Voltage Regulator S10V4F5
Regolatore DC, accetta tensioni da 2.5 a 18VDC in ingresso e produce 5VDC in uscita. Potenza max 400mA -
342850 2850 - Pololu 5V, 2.5A Step-Down Voltage Regulator D24V25F5
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces ifalse -
342851 2851 - Pololu 5V, 5A Step-Down Voltage Regulator D24V50F5
This step-down (buck) regulator generates a fixed 5 V output from input voltages up to 38 V. It is a switching regulator (alsfalse -
342577 2577 - Pololu 12V Step-Up/Step-Down Voltage Regulator S18V20F12
This powerful step-up/step-down regulator efficiently produces a fixed 12 V output from input voltages between 3 V and 30 V wfalse -
342834 2834 - Pololu 12V, 1A Step-Down Voltage Regulator D24V10F12
The compact D24V10F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 1false -
342831 2831 - Pololu 5V, 1A Step-Down Voltage Regulator D24V10F5
The compact D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5false -
342830 2830 - Pololu 3.3V, 1A Step-Down Voltage Regulator D24V10F3
The compact D24V10F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.false -
342843 2843 - Pololu 5V, 500mA Step-Down Voltage Regulator D24V5F5
The compact D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 Vfalse -
342587 2587 - Breakout Board for microSD Card with 3.3V Regulator and Level Shifters
This compact board breaks out the pins of a microSD card connector necessary to interface with the card through SPI (Serial Pfalse -
342855 2855 - Pololu 12V, 2.2A Step-Down Voltage Regulator D24V22F12
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces ifalse -
342812 2812 - Big Pushbutton Power Switch with Reverse Voltage Protection, MP
The Pololu Pushbutton Power Switches are sophisticated power control alternatives to bulky mechanical switches.