This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same.
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is DTR. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.
There are pros and cons to the FTDI Cable vs the FTDI Basic. This board has TX and RX LEDs that allow you to actually see serial traffic on the LEDs to verify if the board is working, but this board requires a Mini-B cable. The FTDI Cable is well protected against the elements, but is large and cannot be embedded into a project as easily. The FTDI Basic uses DTR to cause a hardware reset where the FTDI cable uses the RTS signal.
This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro and LilyPad boards use this type of connector
|Part. No. :||DEV-09873|
Questions on FTDI Basic Breakout - 3.3V
No questions asked yetFai una domanda (Registrati oppure Esegui il Login ).
990004 Adattatore USB->Seriale in miniaturaL'adattatore seriale 990 004 e' ottimo per connettere microcontrollori e circuiti logici al PC. Il cuore del circuito e' il cfalsePrezzo di listino:€ 11,83OffertaTasse escluse:€ 8,20IVA inclusa:€ 10,00
711301 Cavo USB Mini-B 1,8mtCavo USB 2.0 A to Mini-B 5-pin. Ottima qualita', firmato Sparkfun!Tasse escluse:€ 3,68IVA inclusa:€ 4,49
709716 FTDI Basic Breakout - 5VThis is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more cfalseTasse escluse:€ 12,17IVA inclusa:€ 14,85
713678 WiFi Module - ESP8266The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller accesfalseTasse escluse:€ 6,87IVA inclusa:€ 8,38
713711 SparkFun ESP8266 Thing - Dev BoardThis is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely design around the ESP8266, with an infalseTasse escluse:€ 12,84IVA inclusa:€ 15,66
713746 SparkFun Beefy 3 - FTDI Basic BreakoutThis is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI falseTasse escluse:€ 13,50IVA inclusa:€ 16,47
713815 SparkFun Beefcake Relay Control KitThe heart of the board is a sealed, SPDT 20A/10A Relay. The relay is controlled by 5V logic through a transistor, and an LED falseTasse escluse:€ 6,87IVA inclusa:€ 8,38
713830 SparkFun USB UART Serial Breakout - CY7C65213The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the ICTasse escluse:€ 13,17IVA inclusa:€ 16,07
714050 SparkFun Serial Basic Breakout - CH340GThe SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH.Tasse escluse:€ 5,55IVA inclusa:€ 6,77