The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode.
Logic supply voltage (VCC) can be in the range of 2.7-5.5VDC, while the motor supply (VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel (or up to 3.2A for a short, single pulse).
Board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1" pitch headers; the pins are arranged such that input pins are on one side and output pins are on the other.
- Power supply voltage: VM=15V max, VCC=2.7-5.5V
- Output current: Iout=1.2A(average) / 3.2A (peak)
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Built-in thermal shutdown circuit and low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1" spaced pins
- Filtering capacitors on both supply lines
Questions on Motor Driver 1A Dual TB6612FNG
No questions asked yetFai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
711890 MiniMoto - DRV8830 BreakoutMotor Controller basato sul Chip DRV8830, controlla un Motore a spazzole, con tensione da 2,7V a 6,8V e 1A di potenza max. SifalseTasse escluse:€ 8,20IVA inclusa:€ 10,00
807831 2130 - DRV8833 Dual Motor Driver CarrierThis tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair ofalseTasse escluse:€ 4,47IVA inclusa:€ 5,45
807832 2135 - DRV8835 Dual Motor Driver CarrierThis tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pairfalseTasse escluse:€ 4,44IVA inclusa:€ 5,42
807833 713 - TB6612FNG Dual Motor Driver CarrierThis tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectionafalseTasse escluse:€ 4,47IVA inclusa:€ 5,45
807834 2137 - A4990 Dual Motor Driver CarrierThis compact breakout board makes it easy to use Allegro’s A4990 dual motor driver, which can control two bidirectional DC mofalseTasse escluse:€ 7,90IVA inclusa:€ 9,64
342990 2990 - DRV8838 Single Brushed DC Motor Driver CarrierThis tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor.Tasse escluse:€ 3,50IVA inclusa:€ 4,27
342753 2753 - Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi B+This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+ and provides an easy and low-cost solutfalseTasse escluse:€ 6,68IVA inclusa:€ 8,15
713911 SparkFun Serial Controlled Motor DriverIt can be commanded by UART, I2C or SPI communication, and it can drive a constant 1.2A load per motor (peak 1.5A) at 11V. CfalseTasse escluse:€ 14,16IVA inclusa:€ 17,28