342997 2997 - TB9051FTG Single Brushed DC Motor Driver Carrier

2997 - TB9051FTG Single Brushed DC Motor Driver Carrier

Controller con chip Toshiba TB9051FTG, per controllo motori CC. Ampio range di tensione e 2.6A di potenza. Protezioni varie sui picchi di corrente, sovratensione, sotto tensione, etc.
Categorie
Prezzi IVA inclusa
€ 13,42 Prezzo
€ 11,00 + VAT

 

Dettagli

This breakout board makes it easy to use Toshiba’s TB9051FTG brushed DC motor driver. It has a wide operating voltage range of 4.5 V to 28 V and can deliver a continuous 2.6 A. A fixed current chopping threshold allows the TB9051 to limit the peak motor current, and it features built-in protection against under-voltage, over-current, and over-temperature conditions; our carrier board also adds reverse-voltage protection.


The TB9051FTG from Toshiba is an H-bridge motor driver IC that can be used for bidirectional control of a single brushed DC motor at 4.5 V to 28 V. It can supply up to about 2.6 A continuously, and it can deliver peak currents up to 5 A (typical) for a few seconds. The TB9051FTG is a great IC, but its small surface-mount package makes it difficult for the typical student or hobbyist to use; our breakout board makes it easy to use with standard solderless breadboards and 0.1″ perfboards. The board ships populated with SMD components, including the TB9051FTG and a reverse battery protection circuit.

Features

  • Single-channel H-bridge motor driver
  • Motor supply voltage: 4.5 V to 28 V
  • Output current: up to 2.6 A continuous (5 A peak)
  • Automatic current chopping feature helps prevent overheating by gracefully reducing power rather than abruptly shutting down
  • Under-voltage lockout and protection against over-current/short-circuit and over-temperature
  • Carrier board adds reverse-voltage protection
  • Active-low error output indicates over-current, over-temperature, under-voltage, or VCC over-voltage condition
  • Compact size (1.0″ × 1.0″)
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB

Dimensions

Size: 1.0" × 1.0″1
Weight: 3.1 g1

General specifications

Motor driver: TB9051FTG
Motor channels: 1
Minimum operating voltage: 4.5 V2
Maximum operating voltage: 28 V3
Peak output current per channel: 5 A
Continuous output current: 2.6 A
Current sense: 0.5 V/A
Maximum PWM frequency: 20 kHz
Reverse voltage protection?: Y

Identifying markings

PCB dev codes: md36a
Other PCB markings: 0J11154

Notes:

1 Without included hardware.
2 Operation from 4.5 V to 8 V reduces maximum current output.
3 The device is protected for transients up to 40 V.

 

Included hardware

This product ships with all surface-mount components—including the TB9051FTG driver IC—installed as shown in the product picture. However, soldering is required for assembly of the included through-hole parts: one 1×17-pin breakaway 0.1″ male header and two 2-pin, 3.5 mm terminal blocks (for board power and motor outputs).

Product page

Specifiche

Part. No. : 2997

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2997 - TB9051FTG Single Brushed DC Motor Driver Carrier

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. 2992 - Pololu G2 High-Power Motor Driver 24v13

    342992 2992 - Pololu G2 High-Power Motor Driver 24v13

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ ×false
    Tasse escluse:
    € 25,96
    IVA inclusa:
    € 31,67
      Confronta
  2. 2994 - Pololu G2 High-Power Motor Driver 18v25

    342994 2994 - Pololu G2 High-Power Motor Driver 18v25

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ ×false
    Tasse escluse:
    € 32,40
    IVA inclusa:
    € 39,53
      Confronta
  3. 2999 - TB67H420FTG Dual/Single Motor Driver Carrier

    342999 2999 - TB67H420FTG Dual/Single Motor Driver Carrier

    Controller con chip Toshiba TB67H420FTG, per controllo motori CC. Puo' operare in dual-channel oppure in single-channel raddofalse
    Tasse escluse:
    € 15,00
    IVA inclusa:
    € 18,30
      Confronta