342999 2999 - TB67H420FTG Dual/Single Motor Driver Carrier

2999 - TB67H420FTG Dual/Single Motor Driver Carrier

Controller con chip Toshiba TB67H420FTG, per controllo motori CC. Puo' operare in dual-channel oppure in single-channel raddoppiando la potenza. Ampio range di tensioni, potenza continua di 1.7A
Categorie
Prezzi IVA inclusa
€ 18,30 Prezzo
€ 15,00 + VAT

 

Dettagli

This breakout board makes it easy to use Toshiba’s TB67H420FTG brushed DC motor driver, which can operate in either dual-channel mode for independent bidirectional control of two motors or single-channel mode for driving one motor with increased current. It has a wide operating voltage range of 10 V to 47 V and can deliver a continuous 1.7 A to each motor channel, or 3.4 A in single-channel mode. A configurable current chopping threshold allows the TB67H420 to actively limit the motor current, and it features built-in protection against under-voltage, over-current, and over-temperature conditions; our carrier board also adds reverse-voltage protection (up to 40 V)

The TB67H420FTG from Toshiba is an H-bridge motor driver IC that can be used for bidirectional control of one or two brushed DC motors at 10 V to 47 V. It can supply up to about 1.7 A continuously to each of two separate motors or about 3.4 A to a single motor, and it can tolerate peak currents up to 4.5 A per channel (dual) or 9 A (single) for a few seconds, making it a good choice for small- to medium-sized motors that run at higher voltages. The TB67H420FTG is a great IC, but its small surface-mount package makes it difficult for the typical student or hobbyist to use; our breakout board makes it easy to use with standard solderless breadboards and 0.1″ perfboards. Since this board is a carrier for the TB67H420FTG, we recommend careful reading of the TB67H420FTG datasheet (460k pdf). The board ships populated with SMD components, including the TB67H420FTG and a reverse battery protection circuit.

Features

  • Single- or dual-channel H-bridge motor driver (can drive one or two DC motors)
  • Motor supply voltage: 10 V to 47 V
  • Output current:
    • up to 1.7 A continuous (4.5 A peak) per motor in dual-channel mode
    • up to 3.4 A continuous (9 A peak) in single-channel mode
  • Configurable current chopping actively limits motor current to 4.5 A per channel (dual) or 9 A (single) by default; can be lowered with external resistors or voltage sources
  • No separate logic supply needed; inputs are 3V- and 5V-compatible
  • Flexible input interface provides several options for control
  • Under-voltage lockout and protection against over-current/short-circuit and over-temperature
  • Open-load detection
  • Carrier board adds reverse-voltage protection up to 40 V
  • Active-low error outputs indicate over-current, over-temperature, or open-load condition
  • Compact size (1.0″ × 1.2″)
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB

Dimensions

Size: 1.2″ × 1.0″1
Weight: 3.5 g1

General specifications

Motor driver: TB67H420FTG
Motor channels: 2
Minimum operating voltage: 10 V
Maximum operating voltage: 47 V2
Continuous output current per channel: 1.7 A
Continuous paralleled output current: 3.4 A
Reverse voltage protection?: Y2

Identifying markings

PCB dev codes: md35a
Other PCB markings: 0J11169

Notes:

1 Without included hardware.
2 Note: Reverse voltage protection only works up to 40 V.

 

Note: the motor supply capacitors on this carrier are rated for 50 V; this is less margin than on most of our motor driver carriers, which have ICs with ratings of 40 V or less. Please keep this in mind if you want to push the high-voltage limit of this driver.

Product page

Specifiche

Part. No. : 2999

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 2999 - TB67H420FTG Dual/Single Motor Driver Carrier

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. 2992 - Pololu G2 High-Power Motor Driver 24v13

    342992 2992 - Pololu G2 High-Power Motor Driver 24v13

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ ×false
    Tasse escluse:
    € 25,96
    IVA inclusa:
    € 31,67
      Confronta
  2. 2994 - Pololu G2 High-Power Motor Driver 18v25

    342994 2994 - Pololu G2 High-Power Motor Driver 18v25

    This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ ×false
    Tasse escluse:
    € 32,40
    IVA inclusa:
    € 39,53
      Confronta
  3. 2997 - TB9051FTG Single Brushed DC Motor Driver Carrier

    342997 2997 - TB9051FTG Single Brushed DC Motor Driver Carrier

    Controller con chip Toshiba TB9051FTG, per controllo motori CC. Ampio range di tensione e 2.6A di potenza. Protezioni varie sfalse
    Tasse escluse:
    € 11,00
    IVA inclusa:
    € 13,42
      Confronta