This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC). This version offers a wide 6.5 V to 40 V operating range and can deliver continuous output currents up to 13 A without a heat sink.
With integrated support for analog voltage or tachometer (frequency) feedback, the second-generation G2 family of Jrk motor controllers makes it easy to add closed-loop control of speed or position (but not both!) of a single brushed DC motor to a variety of projects. These versatile, general-purpose modules support five different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, and analog voltages for use with a potentiometer or analog joystick. They also offer many settings that can be configured using our free configuration software utility for Windows, Linux, and macOS. This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Jrk G2 to a computer).
Main features of the Jrk G2 family
- Easy open-loop or closed-loop control of one brushed DC motor
- A variety of control interfaces:
- USB for direct connection to a computer
- TTL serial operating at 5 V for use with a microcontroller
- I²C for use with a microcontroller
- RC hobby servo pulses for use in an RC system
- Analog voltage for use with a potentiometer or analog joystick
- Feedback options:
- Analog voltage (0 V to 5 V), for making a closed-loop servo system
- Frequency, for closed-loop speed control using pulse counting (for higher-frequency feedback) or pulse timing (for lower-frequency feedback)
- None, for open-loop speed control
- Note: the Jrk does support using quadrature encoders for position control
- Ultrasonic 20 kHz PWM for quieter operation (can be configured to use 5 kHz instead)
- Simple configuration and calibration over USB with free configuration software utility (for Windows, Linux, and macOS)
- Configurable parameters include:
- PID period and PID coefficients (feedback tuning parameters)
- Maximum current
- Maximum duty cycle
- Maximum acceleration and deceleration
- Error response
- Input calibration (learning) for analog and RC control
- Optional CRC error detection eliminates communication errors caused by noise or software faults
- Reversed-power protection
- Field-upgradeable firmware
- Optional feedback potentiometer disconnect detection
Details for item #3147
The Jrk G2 24v13 operates from 6.5 V to 40 V and can deliver a continuous output current of 13 A without a heat sink. Note that 40 V is the absolute maximum for this controller; the maximum recommended operating voltage is 34 V, and the maximum recommended nominal battery voltage is 28 V.
If you need to identify which version you have, you can just plug it into a computer through USB and the Jrk software will tell you. For quick visual identification without a computer, you can distinguish this version from the identically sized Jrk G2 18v19 by the number 100 on top of the tall silver electrolytic capacitors.
|Size:||1.2″ × 1.4″ × 0.42″1|
|Control interface:||USB; non-inverted TTL serial; I²C;
RC servo pulses; analog voltage
|Minimum operating voltage:||6.5 V|
|Maximum operating voltage:||40 V2|
|Continuous output current per channel:||13 A3|
|Maximum PWM frequency:||20 kHz|
|Reverse voltage protection?:||Y|
|Version:||G2 24v13 (40 V max, 13 A max continuous)|
|PCB dev codes:||umc05a|
|Other PCB markings:||0J11042, blank white box|
- 1 Without included hardware.
- 2 Absolute maximum; higher voltages can permanently destroy the motor driver. Recommended maximum is approximately 34 V, which leaves a safety margin for ripple voltage on the supply line.
- 3 Typical results at room temperature with both channels running at 90% duty cycle.
The Jrk ships with a 0.1″ breakaway male header strip and two 2-pin 5mm terminal blocks. You can solder the terminal blocks to the four large through-holes to make your motor and motor power connections, or you can solder an 8-pin piece of the 0.1″ header strip into the smaller through-holes that border these larger holes. Note, however, that the terminal blocks are only rated for 16 A, and each header pin pair is only rated for a combined 6 A, so for higher-power applications, thick wires should be soldered directly to the board.
|Part. No. :||3147|
Questions on 3147 - Jrk G2 24v13 USB Motor Controller with Feedback
No questions asked yetFai una domanda (Registrati oppure Esegui il Login ).
Tasse escluse:€ 40,45IVA inclusa:€ 49,35
Tasse escluse:€ 72,76IVA inclusa:€ 88,77
Tasse escluse:€ 134,50IVA inclusa:€ 164,09
Tasse escluse:€ 134,50IVA inclusa:€ 164,09
Tasse escluse:€ 89,70IVA inclusa:€ 109,43
Tasse escluse:€ 43,30IVA inclusa:€ 52,83
Tasse escluse:€ 34,50IVA inclusa:€ 42,09
Tasse escluse:€ 43,90IVA inclusa:€ 53,56
Tasse escluse:€ 35,00IVA inclusa:€ 42,70