343753 3753 - Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled)

3753 - Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled)

This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 V operating range and are efficient enough to deliver a continuous 14 A without a heat sink.
Prezzi IVA inclusa
€ 95,16 Prezzo
€ 78,00 + VAT

Qty
 

Dettagli

This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 V operating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation. The default pin mappings make it easy to get started, but they can be customized for more specialized applications. This version ships fully assembled with connectors soldered in.

The minimum operating voltage for all four versions is 6.5 V, while the maximum operating voltages are given in the above table. The board also includes an integrated 5 V, 2.5 A switching step-down regulator that can be used to power the Raspberry Pi it is plugged into, enabling operation from a single power supply.

The driver’s default configuration uses six GPIO pins to control the motor drivers, making use of the Raspberry Pi’s hardware PWM outputs, and it uses two additional pins to read status outputs from the drivers. However, the pin mappings can be customized if the defaults are not convenient, and pins for current sensing and limiting are accessible on the board for more advanced applications.

Note that this motor driver add-on is designed specifically for newer versions of the Raspberry Pi with 40-pin GPIO headers, including the Model B+Model A+Raspberry Pi 2 Model B, and Raspberry Pi 3 Model B. The board matches the Raspberry Pi HAT (Hardware Attached on Top) mechanical specification, although it does not conform to the full HAT specifications due to the lack of an ID EEPROM. (A footprint for adding your own EEPROM is available for applications where one would be useful; pull-ups on SDA, SCL, and WP are provided.) It is not practical to use this expansion board with the original Raspberry Pi Model A or Model B due to differences in their pinout and form factor

Features common to all versions

  • PWM operation up to 100 kHz
  • Motor indicator LEDs show what the outputs are doing even when no motor is connected
  • Integrated 5 V, 2.5 A switching step-down voltage regulator powers the Raspberry Pi base for single-supply operation
  • Python library makes it easy to get started using this board as a motor driver expansion board
  • GPIO pin mappings can be customized if the default mappings are not convenient
  • Current sensing and limiting pins are exposed for advanced use
  • Reverse-voltage protection
  • Undervoltage shutdown
  • Short circuit protection

Dimensions

Size: 65 mm × 56 mm
Weight: 30 g1

General specifications

Motor channels: 2
Minimum operating voltage: 6.5 V
Maximum operating voltage: 36 V2
Continuous output current per channel: 14 A3
Maximum PWM frequency: 100 kHz
Reverse voltage protection?: Y
Partial kit?: N

Identifying markings

PCB dev codes: rpe03b
Other PCB markings: 0J10614, blank white box

Notes:

1 Without included mounting hardware.
2 Absolute maximum; higher voltages can permanently destroy the motor driver. Recommended maximum is approximately 30 V, which leaves a safety margin for ripple voltage on the supply line. Disconnecting on-board regulator increases absolute maximum to 40 V. Not recommended for use with 36 V batteries.
3 Typical results at room temperature with both channels running at 90% duty cycle.

Specifiche

Part. No. : 3753

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 3753 - Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled)

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).