343135 3135 - Tic T500 USB Multi-Interface Stepper Motor Controller

3135 - Tic T500 USB Multi-Interface Stepper Motor Controller

Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controller supporta le seguenti interfacce: USB, seriale TTL, I2C, Analogica, encoder, radio R/C
Prezzi IVA inclusa
€ 22,95 Prezzo
€ 18,81 + VAT

 

Dettagli

The Tic T500 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates an MPS MP6500 driver and male headers and terminal blocks are included but not soldered. It can operate from 4.5 V to 35 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2.5 A max with sufficient additional cooling)

The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial. They also offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer)

Features and specifications

  • Open-loop speed or position control of one bipolar stepper motor
  • A variety of control interfaces:
    • USB for direct connection to a computer
    • TTL serial operating at 5 V for use with a microcontroller
    • I²C for use with a microcontroller
    • RC hobby servo pulses for use in an RC system
    • Analog voltage for use with a potentiometer or analog joystick
    • Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (not for position feedback)
    • STEP/DIR inputs for compatibility with existing stepper motor control firmware
  • Acceleration and deceleration limiting
  • Maximum stepper speed: 50,000 steps per second
  • Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).
  • Up to six different microstep resolutions:
    • The Tic T825 and Tic T834 supports full step, half step, 1/4 step, 1/8 step, 1/16 step, and 1/32 step
    • The Tic T500 supports full step, half step, 1/4 step, 1/8 step
  • Digitally adjustable current limit
  • Optional safety controls to avoid unexpectedly powering the motor
  • Input calibration (learning) and adjustable scaling degree for analog and RC signals
  • 5 V regulator (no external logic voltage supply needed)
  • Optional kill switch inputs
  • Connects to a computer through USB via a USB A to Micro-B cable (not included)
  • Free configuration software available for Windows, Linux, and macOS
  • Comprehensive user’s guide

Dimensions

Size: 1.50″ × 1.05″ × 0.42″1
Weight: 4.8 g1

General specifications

Model: Tic T500
Motor driver: MP6500
Control interface: USB; non-inverted TTL serial; I²C;
RC servo pulses; analog voltage; quadrature encoder
Minimum operating voltage: 4.5 V2
Maximum operating voltage: 35 V
Continuous current per phase: 1.5 A3
Maximum current per phase: 2.5 A4
Maximum step rate: 50000 PPS
Microstep resolutions: full, 1/2, 1/4, and 1/8
Reverse voltage protection?: Y
Connectors soldered?: N

Identifying markings

PCB dev codes: tic03a
Other PCB markings: 0J11038

Notes:

1 Without included optional hardware.
2 Powering the Tic T500 with a supply voltage between 4.5 V and 5.5 V might cause its logic voltage to be lower than normal, which could affect operation. See the user’s guide for more information.
3 Without a heat sink or forced air flow.
4 With sufficient additional cooling.

File downloads

 

Specifiche

Part. No. : 3135

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on 3135 - Tic T500 USB Multi-Interface Stepper Motor Controller

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

    582133 2133 - DRV8825 Stepper Motor Driver Carrier, High Current

    Modulo di controllo per motori passo passo. Gestisce un motore bipolare, fino a 1.5A per fase, fino a 2.2A con dissipatore (nfalse
    Tasse escluse:
    € 7,43
    IVA inclusa:
    € 9,06
      Confronta
  2. 2971 - DRV8880 Stepper Motor Driver Carrier

    342971 2971 - DRV8880 Stepper Motor Driver Carrier

    This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurfalse
    Tasse escluse:
    € 5,84
    IVA inclusa:
    € 7,12
      Confronta
  3. EasyDriver Stepper Motor Driver

    712779 EasyDriver Stepper Motor Driver

    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or false
    Tasse escluse:
    € 10,19
    IVA inclusa:
    € 12,43
      Confronta
  4. 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller

    343131 3131 - Tic T825 USB Multi-Interface Stepper Motor Controller

    The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuratifalse
    Tasse escluse:
    € 65,00
    IVA inclusa:
    € 79,30
      Confronta
  5. 3132 - Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)

    343132 3132 - Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered)

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 64,00
    IVA inclusa:
    € 78,08
      Confronta
  6. 3139 - Tic T249 USB Multi-Interface Stepper Motor Controller

    343139 3139 - Tic T249 USB Multi-Interface Stepper Motor Controller

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 28,84
    IVA inclusa:
    € 35,18
      Confronta
  7. 3140 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller (Connectors Soldered)

    343140 3140 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller (Connectors Soldered)

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 48,56
    IVA inclusa:
    € 59,24
      Confronta
  8. 3141 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller

    343141 3141 - Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller

    Controllo motori stepper (passo-passo) multi interfaccia. Configurabile tramite USB con il software scaricabile. Il controllefalse
    Tasse escluse:
    € 62,00
    IVA inclusa:
    € 75,64
      Confronta