Dettagli
This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging. Its an ESP8266 WiFi module with all the extras you need, ready to rock! We have other boards in the Feather family, check'em out here.
This is the Assembled Adafruit Feather HUZZAH ESP8266 with headers - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging and ready to go immediately! Its an ESP8266 WiFi module with all the extras you need, ready to rock!
At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can progam the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. We wired up a USB-Serial chip that an upload code at a blistering 921600 baud for fast development time. It also has auto-reset so no noodling with pins and reset button pressings.
To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available.
Here's some handy specs!
- Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
- Light as a (large?) feather - 9.7 grams
- ESP8266 @ 80MHz with 3.3V logic/power
- 4MB of FLASH (32 MBit)
- Built in WiFi 802.11 b/g/n
- 3.3V regulator with 500mA peak current output
- CP2104 USB-Serial converter onboard with 921600 max baudrate for uploading
- Auto-reset support for getting into bootload mode before firmware upload
- 9 x GPIO pins - can also be used as I2C and SPI
- 1 x analog inputs 1.0V max
- Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger
- Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking
- Power/enable pin
- 4 mounting holes
- Reset button
Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua. (It comes preprogrammed with the Lua interpretter) We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)
- 23mm x 51mm x 7.2mm / 0.9" x 2" x 0.28"
- Weight: 6.2
Specifiche
Part. No. : | 3046 |
Questions on Assembled Adafruit Feather HUZZAH with ESP8266 WiFi With Headers
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
808524 Adafruit Feather 32u4 Bluefruit LE
This is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with builfalse -
808529 FeatherWing Proto - Prototyping Add-on For All Feather Boards
This is the FeatherWing Proto - a prototyping add-on for all Feather boards. -
808553 Adafruit Feather 32u4 Adalogger
This is the Adafruit Feather 32u4 Adalogger - our take on an 'all-in-one' datalogger (or data-reader) with built in USB and bfalse -
808554 Feather Stacking Headers - 12-pin and 16-pin female headers
These two Female Stacking Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business! -
808581 8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards
This is the 8-Channel PWM or Servo FeatherWing, you can add 8 x 12-bit PWM outputs to your FeatherWing. -
808585 Adafruit Feather HUZZAH with ESP8266 WiFi
This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB anfalse -
808655 Adafruit ATWINC1500 WiFi Breakout with uFL Connector - fw 19.4.4
This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performfalse -
808729 Adafruit Feather M0 RFM69 Packet Radio - 433MHz
This is the Adafruit Feather M0 RFM69 Packet Radio (433 MHz) - our take on an microcontroller with a RFM69 HCW packet radio tfalse -
713907 SparkFun ESP32 Thing
Like the 8266, the ESP32 is a WiFi-compatible microcontroller, but to that it adds support for Bluetooth low-energy (i.e BLEfalse -
808884 OLED Breakout Board - 16-bit Color 1.5" w/microSD holder
This OLED uses the SSD1351 driver chip, which manages the display. You can talk to the driver chip using 4-wire write-only SPfalse -
714155 SparkFun ESP32 Thing Power Control Shield
The SparkFun ESP32 Thing Power Control Shield enables the ESP32 Thing to switch up to 5A of a DC load, providing a wide variefalse -
714430 SparkFun ESP32 Thing Motion Shield
The SparkFun ESP32 Thing Motion Shield is a versatile, motion-sensing addition to our ESP32 Thing. With the Motion Shield’s ofalse -
809147 Assembled Adafruit HUZZAH32 – ESP32 Feather Board - with Stacking Headers
The HUZZAH32 is our ESP32-based Feather, made with the official WROOM32 module. -
121307 WiDo - An Arduino Compatible IoT (internet of thing) Board
Scheda Arduino Compatibile basata su ATmega32U4, include modulo WiFi WG1300, un nodo IoT economico e potente -
715574 SparkFun Thing Plus - Artemis
Scheda Arduino compatibile, con modulo Bluetooth BLE Artemis, 1MB di memoria Flash e 384K di RAM, clock 48/96MHz. Connettori false