120259 RS485 Shield For Arduino

RS485 Shield For Arduino

This motor arduino shield allows Arduino to drive two channel DC motors. It uses a L298P chip which deliveries output current up to 2A each channel.
Categorie
Prezzi IVA inclusa
€ 10,83 Prezzo
€ 8,88 + VAT

 

Dettagli

RS485 is an industrial standard for long dsitance, anti-interferrence and reliable communication.   So we create this RS485 Arduino shield, especially designed for the Arduino controller board. It converts UART/Serial protocol to RS485 protocol.  This board allows Arduino access to industrial standard protocol easily.
In contrast to RS-422, which has a single driver circuit which cannot be switched off, RS-485 drivers use three-state logic allowing individual transmitters to be deactivated. This allows RS-485 to implement linear bus topologies using only two wires. The equipment located along a set of RS-485 wires are interchangeably called nodes, stations or devices.
  • Integrated a standard RS485 port ,a mini RS485 port, RS485 headers
  • Provide the welding areas to make full use of the free space. And more importantly, it's convenient for your DIY design.
  • Switch between automatic mode and manual transmission mode, which expand the scope of application.
  • Besides Tx/Rx interface, there is a switch to block/disable this shield, when Arduino needs to be programmed.
  • Gold immersion PCB. Long pins on the back adapt to most Arduino controllers.
What is RS485?
"RS-485 enables the configuration of inexpensive local networks and multidrop communications links. It offers data transmission speeds of 35 Mbit/s for distandances up to 10 m and 100 kbit/s up to 1200 m. Since it uses a differential balanced line over twisted pair (like RS-422), it can span relatively large distances up to 1,200 m (4,000 ft). A rule of thumb is that the speed in bit/s multiplied by the length in meters should not exceed 108. Thus a 50 meter cable should not signal faster than 2 Mbit/s." From Wiki.
 

 

 

SPECIFICATION

 

 

  • Power module: +5V
  • Module size: 55mmx53mm(2.16"x2.08")
  • 16 digital IO port (including a I2C interface)
  • 6 analog IO port and power
  • Operation and programming mode switch
  • Automatic and manual transceiver mode switch (When in manual transceiver mode, the enable end is the 2nd digital IO port)
  • Transceiver indicating LED
  • Standard RS485 interface, mini RS485 interface and RS485 pins
  • Welding area
  • Reset switch
  • PH2.0 sensor interface for DFRobot RS485 series sensor: URM04 Ultrasonic sensor

 

 

 

DOCUMENTS

 

 

 

 

SHIPPING LIST

 

 

  • RS485 shield     x1

Specifiche

Part. No. : DFR0259
Interfaccia : Seriale
Tensione : 5
Tipo Shield : Comunicazione

Tags prodotto

Usa gli spazi per tag separati. Usa virgolette singole (') per frasi.

Questions on RS485 Shield For Arduino

No questions asked yet

Fai una domanda (Registrati oppure Esegui il Login ).
Fai una domanda (Registrati oppure Esegui il Login ).
  1. RS-485 Breakout

    710124 RS-485 Breakout

    Scheda per comunicazione RS485
    Tasse escluse:
    € 10,19
    IVA inclusa:
    € 12,43
      Confronta
  2. MOD-RS485-ISO - GALVANICALLY ISOLATED RS485 CONVERTER MODULE

    500204 MOD-RS485-ISO - GALVANICALLY ISOLATED RS485 CONVERTER MODULE

    Modulo per comunicazione RS485 / RS422 isolato galvanicamente fino a 3000V
    Tasse escluse:
    € 16,20
    IVA inclusa:
    € 19,76
      Confronta