Dettagli
The SparkFun AutoDriver board is based on the STMicro L6470 dSPIN stepper motor driver. This powerful chip allows you to control a stepper motor with a voltage from 8 to 45V at 3Arms over an SPI connection. The AutoDriver board has been designed to be easily integrated into a project, even with multiple boards. Just connect your motors and your SPI-capable microcontroller and get steppin'!
STMicro’s L6470 is a 3A, 8–45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function. As if that weren’t enough, it also features microstepping support (up to 128 microsteps per full step) and PWM drive voltage limiting. Please keep in mind that the L6470 requires a great deal more configuration and adds software complexity to your system.
Unlike most stepper motor drivers, the dSPIN is controlled over an SPI link. It has an onboard 16MHz oscillator, which allows it to autonomously execute movement commands. That means no more counting steps in your code! It also supports customized acceleration and deceleration profiles to prevent jerky starts and stops. Onboard registers track current speed and location.
This new version of the SparkFun AutoDriver’s hardware is slightly different from the previous revision. It has been modified to make it easier to daisy-chain multiple boards together with simple 10-conductor ribbon cables for data and 6-conductor ribbon cables for control. The library has been updated as well, with more information found in the Hookup Guide below.
The logic supply voltage supports both 3.3V and 5V I/O levels.
GET STARTED WITH THE SPARKFUN AUTODRIVER GUIDE
Features:
- Supports up to 128 Microsteps per Full Step
- Daisy-Chain Capable
- Over-Temperature Detect
- Over-Current Detect
- Under-Voltage Detect
- PWM Drive-Voltage Limiting
- SPI Controlled
- Onboard Oscillator and Speed/Location Registers
- Stall Detection
- 5-bit ADC
Documents:
- Schematic
- Eagle Files
- Hookup Guide
- Datasheet (L6470 dSPIN)
- AutoDriver Library
- GitHub
Specifiche
Part. No. : | BOB-13752 |
Questions on SparkFun AutoDriver - Stepper Motor Driver (v13)
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
709238 Stepper Motor with cable
This is a simple, but very powerful stepper motor with a 4-wire cable attached. -
710846 Motore Passo Passo - NEMA-17 - 48mm - 42BYGHM809
Motore passo passo, form factor NEMA 17, lunghezza 48mm albero escluso. 48N.cm -
711611 AutoDriver - Stepper Motor Controller
Motor Controller per motori Passo Passo bipolari, basato sul chip L6470. Si pilota con protocollo SPIPrezzo di listino:€ 34,25OffertaTasse escluse:€ 23,00IVA inclusa:€ 28,06Prezzo IVA incl.
Confronta -
710848 Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)
Motore Passo Passo con asse filettato. Utilizzabile come attuatore lineare. -
342268 Stepper Motor with 28cm Lead Screw: Bipolar, 200 Steps/Rev, 2.8V, 1.7 A/Phase
This NEMA 17-size hybrid bipolar stepping motor has an integrated 28 cm (11″) threaded rod as its output shaft, turning it infalse -
120043 TB6600 Stepper Motor Driver
TB6600 arduino is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is comfalse