Dettagli
The BlackBoard from SparkFun is everything you need in an Arduino Uno with many extra perks. BlackBoard has all of the hardware peripherals you know and love: 14 Digital I/O pins with 6 PWM pins, 4 Analog Inputs, UART, and SPI with a handful of external interrupt pins. BlackBoard even has an SMD ISP header to connect SPI pins to shields.
We’ve applied every lesson we’ve learned about making a better Uno and created the BlackBoard. The USB to serial is now done with a reversible USB C connector with through hole anchoring and the ubiquitous CH340C requiring fewer driver installs. The power portion of the BlackBoard has been reworked: we upgraded the 3.3V regulator to provide up to 600mA, with full thermal and reverse circuit protection, and added extra decoupling capacitance to increase the sensitivity of the ADC readings. We’ve decreased the brightness of the power LED, pin 13 LED, and the TX/RX LEDs from blinding to just perfect. We’ve added 3.3V voltage translation and a Qwiic connector to the edge of the board to allow for quick and seamless connection to our ever-growing line of I2C based Qwiic products. We’ve even added solder pads to the bottom of the board for D+/D- so you can embed your BlackBoard into a project and run an external USB connection. And finally, we’ve increased the height of the reset button. This doesn’t sound like much, but everyone who’s touched it loves the improvement.
For more advanced users we’ve added an I/O jumper. Cut the trace to 5V and solder a jumper to the 3.3V side and the board will run at 3.3V. This is extremely handy if you have a shield or 3.3V sensitive devices, such as an SPI interface, that needs protecting.
The SparkFun BlackBoard comes fully tested with the Optiboot bootloader and can be easily programmed with the ‘Arduino/Genuino Uno’ option from within Arduino. You can power the BlackBoard over USB or through the barrel jack. The on-board power regulator can handle anything from 7 to 15VDC. The barrel jack can support up to 2 amps while the USB connection is limited to 0.5A. Check out the related items below for a compatible wall-wart power supply.
- ATmega328P microcontroller with Optiboot (UNO) Bootloader
- CH340C USB to Serial IC
- Reinforced and reversible USB C connector
- Built-in Qwiic connection
- Input voltage: 7-15V
- 0-5V outputs with 3.3V compatible inputs
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- ISP Header
- 32k Flash Memory
- 16MHz Clock Speed
- Flat bottom, all SMD construction
Documents:
Schematic
Specifiche
Part. No. : | SPX-15098 |
Tensione : | 3.3, 5 |
Questions on SparkFun BlackBoard C
No questions asked yet
Fai una domanda (Registrati oppure Esegui il Login ).Prodotti correlati
-
500143 Arduino UNO R3 con microcontrollore ATmega328
La nuova scheda Arduino Uno R3. Oltre a tutte le caratteristiche delle schede precedenti, la Uno ora utilizza un ATmega16U2 ifalse -
712757 RedBoard - Programmed with Arduino
Clone Arduino compatibile by Sparkfun. Simile all'arduino duemilanove ma con i connettori compatibili R3. Bootloader Arduino UNO.Prezzo di listino:€ 19,70OffertaTasse escluse:€ 13,00IVA inclusa:€ 15,86Prezzo IVA incl.
Confronta -
809118 WhatsNext - Yellow (Arduino Uno Compatibile)
Microcontroller board based on the the ATmega328. Arduino UNO compatible -
714525 SparkFun RedBoard Edge
Scheda Arduino compatibile, pronta per essere montata a pannello. Ha tutte le caratteristiche della scheda RedBoard con i confalse -
715123 SparkFun RedBoard Qwiic
La famosa RedBoard nella recente versione dotata di connettori Qwiic, compatibile con Arduino UNO