SD21 21 Servo Control Module

21 Servo Control Module

The SD21 is a 21 channel servo controller module.
Prices are VAT included
€32.46 Price
€26.61 + VAT




Technical Specifications :
Voltage Separate terminals or from servo supply when 7.2v battery is used
Number of Servo's 21
Refresh Rate 20mS under all conditions
Control Interface I2C
Microcontrollers Picaxe-18x, BS2p, Atom or BX-24 can be fitted
Position Control Directly programmed in us
Speed Control

From maximum down to 20 seconds for full rotation


The SD21 is a 21 channel servo controller module. It will drive up to 21 RC servo's and maintain a 20mS refresh rate, regardless of the number of servo's used or their positions (pulse widths). It will control both position and speed of the servo's. It's controlled by sending commands to the on-board PIC18F2220 over the I2C bus. There are 3 I2C connectors on the board, any one of which can be used to connect to your controller. Alternatively, many controllers such as the Picaxe, BS2p, Atom, BX-24 etc. can be fitted directly to the module, making this a great animatronics controller.

There are two ways to power the SD21. The first is to used a 5v supply for the processor section and a separate 6v-7.2v supply for the servo's. This is the recommend method, and the 4-way terminal block allows for this option. The logic and servo grounds are internally connected on the PCB. Not everyone wants to use two batteries, so we have allowed for the use of a single (typically 7.2v) battery to power the servo's and the module. To do this place a link on the two pin header below the terminal block. This routes servo power to a low drop 5v regulator which supplies the logic. The connections must be made to the servo terminals on the terminal block - NOT the logic ones. The SD21 monitors the servo battery voltage, which is available for reading from an internal register.

The servo's are plugged directly onto the SD21, with the ground pin (black wire on a hitec servo) nearest the outside of the PCB.

Basic Stamp BS2p or compatible controller
A 24 pin socket on the SD21 will accept a BS2p or compatible controller such as the ATOM or BX-24. The Stamp is fitted with pin 1 nearest the outside of the module and away from the servo connectors. The BS2p P0(pin5)/P1(pin6) are used for the I2C SDA/SCL lines. These are the only I/O pins used on the module, the remainder are brought out on the 16 pin header, as shown above.

Picaxe Controller
A 18 pin socket on the SD21 will accept the PICAXE-18X. Outputs 1 and 4 are used for I2C (they are the hardware I2C port on the PIC) and the remaining inputs and outputs are available on the 16 pin header. The Picaxe is fitted with pin 1 nearest the outside of the module and away from the servo connectors.

Servo Processor
The heart of the SD21 is a pre-programmed PIC18F2220 chip. This is accessed over the I2C bus at address 0xC2 ($C2) by one of the controller options above, fitted to the module, or from an external controller connected to one of the I2C connectors. There are three internal registers associated with each of the 21 servo's. The speed and low byte/high byte of the position.

Register  Servo  Function    Register  Servo  Function   Register  Servo  Function
0 1 Speed   24 9 Speed   48 17 Speed
1 1 Low byte   25 9 Low byte   49 17 Low byte
2 1 High byte   26 9 High byte   50 17 High byte
3 2 Speed   27 10 Speed   51 18 Speed
4 2 Low byte   28 10 Low byte   52 18 Low byte
5 2 High byte   29 10 High byte   53 18 High byte
6 3 Speed   30 11 Speed   54 19 Speed
7 3 Low byte   31 11 Low byte   55 19 Low byte
8 3 High byte   32 11 High byte   56 19 High byte
9 4 Speed   33 12 Speed   57 20 Speed
10 4 Low byte   34 12 Low byte   58 20 Low byte
11 4 High byte   35 12 High byte   59 20 High byte
12 5 Speed   36 13 Speed   60 21 Speed
13 5 Low byte   37 13 Low byte   61 21 Low byte
14 5 High byte   38 13 High byte   62 21 High byte
15 6 Speed   39 14 Speed   63 -  
16 6 Low byte   40 14 Low byte   64 - Software version
17 6 High byte   41 14 High byte   65 - Battery Volts
18 7 Speed   42 15 Speed        
19 7 Low byte   43 15 Low byte        
20 7 High byte   44 15 High byte        
21 8 Speed   45 16 Speed        
22 8 Low byte   46 16 Low byte        
23 8 High byte   47 16 High byte        

Servo Position
The position (low byte/high byte) is a 16 bit number which directly sets the output pulse width in uS. Setting the position to 1500 (1500uS or 1.5mS) will set most servo's to their center position. The range of pulse widths that are normally supported are from 1000uS (1mS) to 2000uS (2mS). It is usually possible to go beyond these limits though. On a Hitec HS311 servo, we can set the position from 800 to 2200 to give a nice wide range of movement. Take care though as its easy to make the servo run into its internal stops if you give it pulse widths at the upper or lower extremes. The registers can also be read back. The position will be the current position of the servo during a speed controlled movement, so you can track its progress towards the requested position.

Servo Speed
The speed register controls the speed at which the servo moves to its new position. The servo pulses are automatically refreshed every 20mS. If the Speed register is zero (0x00) then the servo is simply set to the requested position. On power up the Speed registers are set to zero to give full speed, so unless you need to slow them down the Speed registers can be ignored. If the Speed register is set to something other than zero then that value is added to the current position every 20mS until the target position is reached. If you wish to move from 1000 to 2000 and the Speed register is set to 10, then it will take 2 seconds to reach the set position. The formula for the time it will take to make the move is:
((Target position-Start position)/Speed Reg)*20mS
Here are some examples:

Start Position   Target Position   Speed Reg   Time for Move
2000 1000 10 2000mS (2Sec)
1000 2000 10 2000mS (2Sec)
1000 2000 1 20000mS (20Sec)
1000 2000 100 200mS (0.2Sec)
1234 1987 69 220mS (0.22Sec)

More Registers!
The servo's can be fully controlled by the above registers, however to make things easier for low resource controllers such as the Picaxe, there is another set of registers (63-83 inclusive). These can set the position by writing a single byte rather than two bytes. These are not physically implemented registers, so cannot be read back. When you write to them, the processor will multiply the number you write by 6 then add an offset of 732 and store the result in the real 16-bit registers described above. This gives you a range of 732 (0*6+732) to 2268 (256*6+732) in 6uS steps. This set of registers is called the Base set. The formula is:
Base Reg*6+732uS
Although you can't read them back, the data is stored internally, and used with another two sets of registers. These are positive (84-104) and negative (105-125) offsets. When you write to the positive offset address the processor will add it to the base position, multiply by 6 and add 732. It performs a similar function for negative offsets. the formulas are:
(BaseReg + PosReg) * 6 + 732 and
(BaseReg - NegReg) * 6 + 732

Servo   Base Reg   Pos Offset Reg   Neg Offset Reg 
1 63 84 105
2 64 85 106
3 65 86 107
4 66 87 108
5 67 88 109
6 68 89 110
7 69 90 111
8 70 91 112
9 71 92 113
10 72 93 114
11 73 94 115
12 74 95 116
13 75 96 117
14 76 97 118
15 77 98 119
16 78 99 120
17 79 100 121
18 80 101 122
19 81 102 123
20 82 102 124
21 83 104 125

Register Summery
For precision control of the servo's there is the real 16-bit registers which sets the servo position directly in uS. For low resource controllers the servo's can be controlled by 8-bit values. The positive and negative offset registers make designing walking robots very easy where legs can be easily moved either side of a central position. We have examples of controlling a Lynxmotion EH2 robot with a BS2p Stamp using the 16-bit registers and the Picaxe doing the same using the 8-bit Base and Offset registers.

Software Revision Number
Register 64  is the software revision number (3 at the time of writing this).

Battery Voltage
Register 65 contains the servo battery voltage in 39mV units up to a maximum of 10v. A battery voltage of 7.2v will read about 184. 6v will read about 154. It is updated every 20mS whether its read or not.

The SD21 Servo module is located at address 0xC2 on the I2C bus.

Example Code
This shows how to use a BS2p Stamp to control a servo. It sets up a simple loop which sends the servo between two positions

'{$STAMP BS2p}

SDA     CON 0     ' SDA on pin0, SCL on pin1
SD21    CON $C2   ' SD21 I2C address
Servo1  CON 0     ' register address of servo1 speed reg (followed by pos low/pos high)
Speed   CON 0     ' maximum speed
Servo1p CON 1800  ' Right position
Servo1n CON 1200  ' Left position

Servo VAR W0

  Servo = Servo1p
  I2COUT SDA, SD21, Servo1, [Speed, Servo.LOWBYTE, Servo.HIGHBYTE]
  PAUSE 300
  Servo = Servo1n
  I2COUT SDA, SD21, Servo1, [Speed, Servo.LOWBYTE, Servo.HIGHBYTE]
  PAUSE 300
  GOTO Loop

This does the same for the Picaxe controller using the alternative register set.

Servo1  = 63   ' servo 1 base register
Servo1p = 84   ' servo 1 positive offset register
Servo1n = 105  ' servo 1 negative offset register
Base    = 128  ' centre position
Offset  = 50   ' +/- 50 from centre position

  i2cslave $c2, i2cslow, i2cbyte    ' setup i2c port for servo controller
  writei2c Servo1, (Base)
  writei2c Servo1p, (Offset)
  pause 300
  writei2c Servo1n, (Offset)
  pause 300
  goto Loop

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on 21 Servo Control Module

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.

Price Match

* Required Fields