713752 SparkFun AutoDriver - Stepper Motor Driver (v13)

SparkFun AutoDriver - Stepper Motor Driver (v13)

STMicro's L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function.
Prices are VAT included
€38.43 Price
€31.50 + VAT

Qty
 

Details

The SparkFun AutoDriver board is based on the STMicro L6470 dSPIN stepper motor driver. This powerful chip allows you to control a stepper motor with a voltage from 8 to 45V at 3Arms over an SPI connection. The AutoDriver board has been designed to be easily integrated into a project, even with multiple boards. Just connect your motors and your SPI-capable microcontroller and get steppin'!

STMicro’s L6470 is a 3A, 8–45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function. As if that weren’t enough, it also features microstepping support (up to 128 microsteps per full step) and PWM drive voltage limiting. Please keep in mind that the L6470 requires a great deal more configuration and adds software complexity to your system.

Unlike most stepper motor drivers, the dSPIN is controlled over an SPI link. It has an onboard 16MHz oscillator, which allows it to autonomously execute movement commands. That means no more counting steps in your code! It also supports customized acceleration and deceleration profiles to prevent jerky starts and stops. Onboard registers track current speed and location.

This new version of the SparkFun AutoDriver’s hardware is slightly different from the previous revision. It has been modified to make it easier to daisy-chain multiple boards together with simple 10-conductor ribbon cables for data and 6-conductor ribbon cables for control. The library has been updated as well, with more information found in the Hookup Guide below.

The logic supply voltage supports both 3.3V and 5V I/O levels.

GET STARTED WITH THE SPARKFUN AUTODRIVER GUIDE

Features:

  • Supports up to 128 Microsteps per Full Step
  • Daisy-Chain Capable
  • Over-Temperature Detect
  • Over-Current Detect
  • Under-Voltage Detect
  • PWM Drive-Voltage Limiting
  • SPI Controlled
  • Onboard Oscillator and Speed/Location Registers
  • Stall Detection
  • 5-bit ADC

Documents:

Specifications

Part. No. : BOB-13752

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Questions on SparkFun AutoDriver - Stepper Motor Driver (v13)

No questions asked yet

Register or Login to ask a question.
Register or Login to ask a question.
  1. Stepper Motor with cable

    709238 Stepper Motor with cable

    This is a simple, but very powerful stepper motor with a 4-wire cable attached.
    Excl. Tax:
    €14.88
    Incl. Tax:
    €18.15
      Compare
  2. Stepper Motor - NEMA-17 - 48mm - 42BYGHM809

    710846 Stepper Motor - NEMA-17 - 48mm - 42BYGHM809

    Stepper, NEMA17 form-factor. Length:48mm shaft escluded. Holding Torque: 58oz.in
    Excl. Tax:
    €15.39
    Incl. Tax:
    €18.78
      Compare
  3. AutoDriver - Stepper Motor Controller

    711611 AutoDriver - Stepper Motor Controller

    STMicro's L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, ofalse
    Regular Price:
    €32.85
    Special
    Excl. Tax:
    €23.00
    Incl. Tax:
    €28.06
      Compare
  4. Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)

    710848 Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)

    These steppers have a threaded shaft, which allows them to be used as a linear actuator. As the motor runs, it moves along thfalse
    Excl. Tax:
    €28.22
    Incl. Tax:
    €34.43
      Compare
  5. Stepper Motor with 28cm Lead Screw: Bipolar, 200 Steps/Rev, 2.8V, 1.7 A/Phase

    342268 Stepper Motor with 28cm Lead Screw: Bipolar, 200 Steps/Rev, 2.8V, 1.7 A/Phase

    This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 stefalse
    Excl. Tax:
    €50.92
    Incl. Tax:
    €62.12
      Compare
  6. Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)

    713656 Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)

    These steppers have a threaded shaft, which allows them to be used as a linear actuator. As the motor runs, it moves along thfalse
    Excl. Tax:
    €23.73
    Incl. Tax:
    €28.95
      Compare

Price Match



* Required Fields